3M 2273M-iD, 2250M-iD manual Self Test Of Receiver, Menu 6 + More SK4 + Self Test SK7

Page 58

21.3M™ Dynatel™ PC Tool Kit and Locator Software Upgrades

Locator software upgrades are periodically released and can be downloaded, free of charge, at www.3M.com/dynatel. Located under the Software Updates section, the software link is titled Dynatel M-Series Locator PC Tools. To download the software, click on the link and then select Dynatel M-Series Underground Locator PC Tools. Selecting this link will display the latest software downloads as well as any Release Notes related to the current software release.

Once downloaded to your PC, double click the file and an auto-installer will install the C Tool desktop software. Double click the Dynatel PC Tool Kit icon on the desktop. Using the provided RS232 cable, or RS232-to-USB adapter cable, connect the Serial Port [14] on the locator to the PC and power the locator on. Click the Upgrade Software button in PC Tools to begin upgrade. Do not disconnect or power off the locator while the upgrade is in progress. Wait until the software indicates that the installation was successful. This will take approximately six to seven minutes to complete.

The Dynatel PC Tool Kit provides the user an excellent interface between the receiver and a PC. This software utility provides the tools by which the user can:

•Upgrade the receiver to the latest software revision

•Program one or multiple receivers to best suit specific user configurations

•Load an alternate language into the receiver

•Utilize the 3M™ iD Marker utility to:

−− Create templates for writing data to iD markers, or create Trace Templates for GPS path tracing when connected to a GPS device.

−− Download iD marker data that has been written or read by the receiver for documentation databases.

Embedded in the desktop software is the most current software for the receiver, which affords the user the option of upgrading the unit without returning the unit to the 3M Service and Repair Center.

Please refer to the operating instructions included with the software.

22. Self Test Of Receiver

Menu [6] + >>More [SK:4] + Self Test [SK:7]

This operation performs a self-test on the receiver.

The receiver will display current information about the unit (model number, serial number, software revision, and hardware revision).

1.Press Run [SK] to start the self test.

−− A status bar will appear while the self test is running.

−− Results will appear on the display when the test is complete.

58

78-8130-6150-0 Rev G

Page 57 Page 59
Image 58
Page 57 Page 59
Contents 3M Dynatel Contents Rev G Rev G Rev G Safety Information Intended UseAbout This Manual Transmitter Battery Installation Quick StartReceiver Battery Installation Cleaning Service and Accessories3M Dynatel Transmitter 2273 Keypad and Connector Definitions Rechargeable Battery Maximum Transmitter Output3M Dynatel Receiver 2250M Key Pad and Display Definitions Dynatel3M Dynatel Receiver 2273M Key Pad and Display Definitions Menu Displays Main MenuRev G Rev G Select Depth Units Configuring The ReceiverSetting the Receiver Clock Selecting a LanguageEnabling/Disabling Frequencies Menu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6jCreating User Defined Frequencies Filtering Power Frequency Interference Selecting Locating AudioBuried Cables And Pipes Transmitter Connections Direct Connect MethodRev G Dyna-Coupler Method Non-Sweeping Passive Induction Mode Locating Induction MethodSweeping Active Induction Mode Locating Passive SweepsOne-person Active Induction Mode Sweeps Two-person Active Induction Mode Sweeps Transmitter Set-upReceiver Modes Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK ToggleLocate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK Toggle Directional Peak Dir PkLocate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK Toggle Special Peak Spl PkDepth and Current Estimate Expanded ModeLocate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK Toggle Induction Peak Ind PkLocating Frequencies Active FrequenciesPassive Frequencies Power FrequenciesAuxiliary Frequencies Locating in Directional Peak Mode Rev G Locating Active Duct Probes Sondes Determining ADP DepthLocating Buried Sheath Faults and Earth Return Faults Transmitter SetupPinpointing the Buried Fault Green Band Locating 3M Electronic Markers 3M iD Markers Alert ModeEnabling/Disabling Marker Types Single Marker Locate Press Locate/OKDual Marker Locate 3M iD Marker DepthPassive 3M Electronic Marker Non-iD Depth Creating New Templates Creating/Editing Templates for 3M iD MarkersMenu 6 + Data/Templat SK2 + User Templat SK2c Rev G Editing Templates Menu 6 + Write Mode SK1 Writing 3M iD MarkersPress Start Write SK Press Menu 6 + Write Mode SK1 Modifying Marker Data to be WrittenRev G Reading 3M iD Markers Read History Reviewing Marker Read/Write HistoryMenu 6 + Data/Templat SK2 + Read History SK2a Write History SK Capturing the GPS Coordinates Capture Mode / ModeGPS Operation Communicating with the GPS DeviceMenu 6 + COM Setup SK3 + GIS Path Mapping with GPSCreating Trace Templates Menu 6 + Com SK3 + GIS SK or PDA SKAerial Faults Toning Additional ApplicationsConnection Diagrams Cable IdentificationHelp Mode Menu 6 + More SK4 + Help SK8Self Test Of Receiver Menu 6 + More SK4 + Self Test SK7Product Description Product Description And Optional AccessoriesStandard Configurations Direct Connect Cables Earth Contact FrameOptional 3M Accessories for 3M Dynatel Locators Receiver Specifications SpecificationDetection Depth 3M Non-iD Passive Transmitter Specifications Mode can display a fault resistance up to 10M ΩEnvironmental and Regulatory Specifications Rechargeable Battery InformationRev G Electrical Markets Division Important Notice
Top Page Image Contents