3M 2250M-iD, 2273M-iD manual Receiver Battery Installation

Page 9

B. Receiver Battery Installation

Remove cap from receiver handle.

Install eight ‘AA’ size alkaline cell batteries (LR6) into the battery holder as indicated by the polarity symbols (+ and –).

Attach battery holder to the PP3 connector in the receiver handle, and slide holder into the handle. Replace the cap.

8 “AA” (LR6) Alkaline Batteries

1. Twist cap to open battery compartment.

2. Slide battery compartment out of handle.

!Caution

To reduce the risks associated with fire and explosion:

•Do not short, excessively heat, or dispose of batteries in fire.

•Install batteries with proper polarity.

•Use only Alkaline "AA" (LR 6) sized batteries.

•Do not charge batteries

•Do not use leaking batteries

To reduce the risks associated with environmental contamination:

•Dispose of batteries and electronic components in accordance with all regulations.

•Ensure batteries are installed with correct polarity.

•Always remove batteries when storing the units for long periods of time.

The receiver batteries are tested for two seconds every time the unit is turned on.

The bar graph on the display will fill to the relative battery level.

78-8130-6150-0 Rev G

9

Image 9

Contents 3M Dynatel Contents Rev G Rev G Rev G Intended Use Safety InformationAbout This Manual Quick Start Transmitter Battery InstallationReceiver Battery Installation Service and Accessories Cleaning3M Dynatel Transmitter 2273 Keypad and Connector Definitions Maximum Transmitter Output Rechargeable BatteryDynatel 3M Dynatel Receiver 2250M Key Pad and Display Definitions3M Dynatel Receiver 2273M Key Pad and Display Definitions Main Menu Menu DisplaysRev G Rev G Setting the Receiver Clock Configuring The ReceiverSelect Depth Units Selecting a LanguageMenu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6j Enabling/Disabling FrequenciesCreating User Defined Frequencies Selecting Locating Audio Filtering Power Frequency InterferenceDirect Connect Method Buried Cables And Pipes Transmitter ConnectionsRev G Dyna-Coupler Method Induction Method Non-Sweeping Passive Induction Mode LocatingPassive Sweeps Sweeping Active Induction Mode LocatingOne-person Active Induction Mode Sweeps Transmitter Set-up Two-person Active Induction Mode SweepsLocate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK Toggle Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK ToggleReceiver Modes Directional Peak Dir PkSpecial Peak Spl Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK ToggleLocate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK Toggle Expanded ModeDepth and Current Estimate Induction Peak Ind PkActive Frequencies Locating FrequenciesPower Frequencies Passive FrequenciesAuxiliary Frequencies Locating in Directional Peak Mode Rev G Determining ADP Depth Locating Active Duct Probes SondesTransmitter Setup Locating Buried Sheath Faults and Earth Return FaultsPinpointing the Buried Fault Green Band Alert Mode Locating 3M Electronic Markers 3M iD MarkersEnabling/Disabling Marker Types Press Locate/OK Single Marker Locate3M iD Marker Depth Dual Marker LocatePassive 3M Electronic Marker Non-iD Depth Creating/Editing Templates for 3M iD Markers Creating New TemplatesMenu 6 + Data/Templat SK2 + User Templat SK2c Rev G Editing Templates Writing 3M iD Markers Menu 6 + Write Mode SK1Press Start Write SK Modifying Marker Data to be Written Press Menu 6 + Write Mode SK1Rev G Reading 3M iD Markers Reviewing Marker Read/Write History Read HistoryMenu 6 + Data/Templat SK2 + Read History SK2a GPS Operation Capturing the GPS Coordinates Capture Mode / ModeWrite History SK Communicating with the GPS DevicePath Mapping with GPS Menu 6 + COM Setup SK3 + GISMenu 6 + Com SK3 + GIS SK or PDA SK Creating Trace TemplatesAdditional Applications Aerial Faults ToningCable Identification Connection DiagramsMenu 6 + More SK4 + Help SK8 Help ModeMenu 6 + More SK4 + Self Test SK7 Self Test Of ReceiverStandard Configurations Product Description And Optional AccessoriesProduct Description Direct Connect Cables Earth Contact FrameOptional 3M Accessories for 3M Dynatel Locators Specification Receiver SpecificationsDetection Depth 3M Non-iD Passive Mode can display a fault resistance up to 10M Ω Transmitter SpecificationsRechargeable Battery Information Environmental and Regulatory SpecificationsRev G Important Notice Electrical Markets Division