3M 2250M-iD, 2273M-iD manual Press Start Write SK

Page 47

Step 3. Press Menu/OK

−− The selected template will be displayed.

−− The arrow on the right side of the display indicates there is more information than can be displayed on the screen (scroll down by pressing the down arrow [SK]).

Step 4. Enter user information that will be written to this marker. (See 15.A Modifying Marker Data to be Written)

Step 5. Verify that all information is correct

Step 6. Hold the locator directly over the top of the marker. The locator should be within the following maximum writing ranges for each

of the different 3M™ iD Marker formats;

−− Near Surface iD Marker = 6 in (15 cm) maximum

−− Ball iD Marker = 12 in (30 cm) maximum

−− Full Range iD Marker = 24 in (61 cm) maximum

Step 7. Press Start Write [SK].

78-8130-6150-0 Rev G

47

Image 47

Contents 3M Dynatel Contents Rev G Rev G Rev G Intended Use Safety InformationAbout This Manual Quick Start Transmitter Battery InstallationReceiver Battery Installation Service and Accessories Cleaning3M Dynatel Transmitter 2273 Keypad and Connector Definitions Maximum Transmitter Output Rechargeable BatteryDynatel 3M Dynatel Receiver 2250M Key Pad and Display Definitions3M Dynatel Receiver 2273M Key Pad and Display Definitions Main Menu Menu DisplaysRev G Rev G Selecting a Language Configuring The ReceiverSetting the Receiver Clock Select Depth UnitsCreating User Defined Frequencies Menu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6jEnabling/Disabling Frequencies Selecting Locating Audio Filtering Power Frequency InterferenceDirect Connect Method Buried Cables And Pipes Transmitter ConnectionsRev G Dyna-Coupler Method Induction Method Non-Sweeping Passive Induction Mode LocatingPassive Sweeps Sweeping Active Induction Mode LocatingOne-person Active Induction Mode Sweeps Transmitter Set-up Two-person Active Induction Mode SweepsDirectional Peak Dir Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK ToggleLocate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK Toggle Receiver ModesSpecial Peak Spl Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK ToggleInduction Peak Ind Pk Expanded ModeLocate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK Toggle Depth and Current EstimateActive Frequencies Locating FrequenciesAuxiliary Frequencies Power FrequenciesPassive Frequencies Locating in Directional Peak Mode Rev G Determining ADP Depth Locating Active Duct Probes SondesTransmitter Setup Locating Buried Sheath Faults and Earth Return FaultsPinpointing the Buried Fault Green Band Enabling/Disabling Marker Types Alert ModeLocating 3M Electronic Markers 3M iD Markers Press Locate/OK Single Marker Locate3M iD Marker Depth Dual Marker LocatePassive 3M Electronic Marker Non-iD Depth Menu 6 + Data/Templat SK2 + User Templat SK2c Creating/Editing Templates for 3M iD MarkersCreating New Templates Rev G Editing Templates Writing 3M iD Markers Menu 6 + Write Mode SK1Press Start Write SK Modifying Marker Data to be Written Press Menu 6 + Write Mode SK1Rev G Reading 3M iD Markers Menu 6 + Data/Templat SK2 + Read History SK2a Reviewing Marker Read/Write HistoryRead History Communicating with the GPS Device Capturing the GPS Coordinates Capture Mode / ModeGPS Operation Write History SKPath Mapping with GPS Menu 6 + COM Setup SK3 + GISMenu 6 + Com SK3 + GIS SK or PDA SK Creating Trace TemplatesAdditional Applications Aerial Faults ToningCable Identification Connection DiagramsMenu 6 + More SK4 + Help SK8 Help ModeMenu 6 + More SK4 + Self Test SK7 Self Test Of ReceiverDirect Connect Cables Earth Contact Frame Product Description And Optional AccessoriesStandard Configurations Product DescriptionOptional 3M Accessories for 3M Dynatel Locators Specification Receiver SpecificationsDetection Depth 3M Non-iD Passive Mode can display a fault resistance up to 10M Ω Transmitter SpecificationsRechargeable Battery Information Environmental and Regulatory SpecificationsRev G Important Notice Electrical Markets Division