3M 2250M-iD, 2273M-iD Enabling/Disabling Frequencies, Creating User Defined Frequencies

Page 19

D. Enabling/Disabling Frequencies

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + Locate Freq [SK:6g]

The user can select the frequencies that the receiver will detect. All the available frequencies are listed in four groups (Left to Right: Active, Power, Passive, and Auxiliary). The Auxiliary group also contains the User Defined Frequencies. (See Creating User Defined Frequencies, Section 5F.)

1.Press the right arrow [SK] to move the highlight bar to the section of frequencies to enable, or disable.

2.Press the up/down arrows [SK] to highlight the specific frequency.

3.Press Enabl/Disabl [SK]. (Enable denoted by )

4.Repeat steps 2 & 3 to enable/disable other frequencies.

5.Press Locate/OK [5] to save.

E. Selecting External Jack [14] ([13] on 2250M locator) Frequencies (Tone Frequencies)

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + Tone Freq [SK:6j]

A coupler can be plugged into the External Jack [14] ([13]) on 2250M locator) of the receiver and used to identify cables. (See Additional Applications: Cable Identification, Section 19B.) The same procedure

as D. Enabling/Disabling Frequencies (above) is followed for selecting frequencies that can be detected by the External Jack [14] ([13]) on 2250M locator) found on the bottom of the receiver.

F. Creating User Defined Frequencies

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + Locate Freq [SK:6g]

There are four user defined frequencies available on the receiver. (These frequencies must be between 50 Hz and 999 Hz.) These frequencies are found in the column on the far right of the Locate Freq display (Auxiliary frequencies). These frequencies, once programmed, will appear in the Locate mode under the Aux [SK] frequency list when Freq [SK] is selected in the Locate mode.

78-8130-6150-0 Rev G

19

Image 19

Contents 3M Dynatel Contents Rev G Rev G Rev G Intended Use Safety InformationAbout This Manual Quick Start Transmitter Battery InstallationReceiver Battery Installation Service and Accessories Cleaning3M Dynatel Transmitter 2273 Keypad and Connector Definitions Maximum Transmitter Output Rechargeable BatteryDynatel 3M Dynatel Receiver 2250M Key Pad and Display Definitions3M Dynatel Receiver 2273M Key Pad and Display Definitions Main Menu Menu DisplaysRev G Rev G Selecting a Language Configuring The ReceiverSetting the Receiver Clock Select Depth UnitsEnabling/Disabling Frequencies Menu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6jCreating User Defined Frequencies Selecting Locating Audio Filtering Power Frequency InterferenceDirect Connect Method Buried Cables And Pipes Transmitter ConnectionsRev G Dyna-Coupler Method Induction Method Non-Sweeping Passive Induction Mode LocatingPassive Sweeps Sweeping Active Induction Mode LocatingOne-person Active Induction Mode Sweeps Transmitter Set-up Two-person Active Induction Mode SweepsDirectional Peak Dir Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK ToggleLocate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK Toggle Receiver ModesSpecial Peak Spl Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK ToggleInduction Peak Ind Pk Expanded ModeLocate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK Toggle Depth and Current EstimateActive Frequencies Locating FrequenciesPassive Frequencies Power FrequenciesAuxiliary Frequencies Locating in Directional Peak Mode Rev G Determining ADP Depth Locating Active Duct Probes SondesTransmitter Setup Locating Buried Sheath Faults and Earth Return FaultsPinpointing the Buried Fault Green Band Locating 3M Electronic Markers 3M iD Markers Alert ModeEnabling/Disabling Marker Types Press Locate/OK Single Marker Locate3M iD Marker Depth Dual Marker LocatePassive 3M Electronic Marker Non-iD Depth Creating New Templates Creating/Editing Templates for 3M iD MarkersMenu 6 + Data/Templat SK2 + User Templat SK2c Rev G Editing Templates Writing 3M iD Markers Menu 6 + Write Mode SK1Press Start Write SK Modifying Marker Data to be Written Press Menu 6 + Write Mode SK1Rev G Reading 3M iD Markers Read History Reviewing Marker Read/Write HistoryMenu 6 + Data/Templat SK2 + Read History SK2a Communicating with the GPS Device Capturing the GPS Coordinates Capture Mode / ModeGPS Operation Write History SKPath Mapping with GPS Menu 6 + COM Setup SK3 + GISMenu 6 + Com SK3 + GIS SK or PDA SK Creating Trace TemplatesAdditional Applications Aerial Faults ToningCable Identification Connection DiagramsMenu 6 + More SK4 + Help SK8 Help ModeMenu 6 + More SK4 + Self Test SK7 Self Test Of ReceiverDirect Connect Cables Earth Contact Frame Product Description And Optional AccessoriesStandard Configurations Product DescriptionOptional 3M Accessories for 3M Dynatel Locators Specification Receiver SpecificationsDetection Depth 3M Non-iD Passive Mode can display a fault resistance up to 10M Ω Transmitter SpecificationsRechargeable Battery Information Environmental and Regulatory SpecificationsRev G Important Notice Electrical Markets Division