3M 2250M-iD, 2273M-iD manual Filtering Power Frequency Interference, Selecting Locating Audio

Page 20

To program the user defined frequencies press the right arrow [SK] to highlight the Auxiliary group of frequencies. Press the up/down arrows [SK] to highlight the user frequency to program. Press Enabl/Disabl [SK].

Press the left/right arrows [SK] to move the square cursor to a digit. Press Select [SK] to enter the number in the frequency field.

Press Locate/OK [5] to save the programmed frequency, or press Exit [SK] to cancel. The frequency will appear in the locate frequency display as U ###, where ### represents the selected frequency.

Note: To redefine a previously programmed user frequency, highlight the frequency, press enabl/ disabl, select the back arrow with the cursor, and press select to delete the previous entry.

G. Filtering Power Frequency Interference

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + >>More [SK:6h] + Filter [SK:6k]

In order to filter out unwanted power influences while locating with user-defined frequencies, verify the correct frequency is selected for your location (default is 60 Hz). Press Locate/OK [5].

H. Selecting Locating Audio

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + >>More [SK:6h] + Audio Config [SK:6l]

The user can choose the audio response of the receiver when using the Directional Peak mode for path locating. Highlight the audio selection and press Locate/OK [5] to save.

20

78-8130-6150-0 Rev G

Image 20
Contents 3M Dynatel Contents Rev G Rev G Rev G Safety Information Intended UseAbout This Manual Transmitter Battery Installation Quick StartReceiver Battery Installation Cleaning Service and Accessories3M Dynatel Transmitter 2273 Keypad and Connector Definitions Rechargeable Battery Maximum Transmitter Output3M Dynatel Receiver 2250M Key Pad and Display Definitions Dynatel3M Dynatel Receiver 2273M Key Pad and Display Definitions Menu Displays Main MenuRev G Rev G Configuring The Receiver Setting the Receiver ClockSelect Depth Units Selecting a LanguageCreating User Defined Frequencies Menu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6jEnabling/Disabling Frequencies Filtering Power Frequency Interference Selecting Locating AudioBuried Cables And Pipes Transmitter Connections Direct Connect MethodRev G Dyna-Coupler Method Non-Sweeping Passive Induction Mode Locating Induction MethodSweeping Active Induction Mode Locating Passive SweepsOne-person Active Induction Mode Sweeps Two-person Active Induction Mode Sweeps Transmitter Set-upLocate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK Toggle Locate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK ToggleReceiver Modes Directional Peak Dir PkLocate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK Toggle Special Peak Spl PkExpanded Mode Locate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK ToggleDepth and Current Estimate Induction Peak Ind PkLocating Frequencies Active FrequenciesAuxiliary Frequencies Power FrequenciesPassive Frequencies Locating in Directional Peak Mode Rev G Locating Active Duct Probes Sondes Determining ADP DepthLocating Buried Sheath Faults and Earth Return Faults Transmitter SetupPinpointing the Buried Fault Green Band Enabling/Disabling Marker Types Alert ModeLocating 3M Electronic Markers 3M iD Markers Single Marker Locate Press Locate/OKDual Marker Locate 3M iD Marker DepthPassive 3M Electronic Marker Non-iD Depth Menu 6 + Data/Templat SK2 + User Templat SK2c Creating/Editing Templates for 3M iD MarkersCreating New Templates Rev G Editing Templates Menu 6 + Write Mode SK1 Writing 3M iD MarkersPress Start Write SK Press Menu 6 + Write Mode SK1 Modifying Marker Data to be WrittenRev G Reading 3M iD Markers Menu 6 + Data/Templat SK2 + Read History SK2a Reviewing Marker Read/Write HistoryRead History Capturing the GPS Coordinates Capture Mode / Mode GPS OperationWrite History SK Communicating with the GPS DeviceMenu 6 + COM Setup SK3 + GIS Path Mapping with GPSCreating Trace Templates Menu 6 + Com SK3 + GIS SK or PDA SKAerial Faults Toning Additional ApplicationsConnection Diagrams Cable IdentificationHelp Mode Menu 6 + More SK4 + Help SK8Self Test Of Receiver Menu 6 + More SK4 + Self Test SK7Product Description And Optional Accessories Standard ConfigurationsProduct Description Direct Connect Cables Earth Contact FrameOptional 3M Accessories for 3M Dynatel Locators Receiver Specifications SpecificationDetection Depth 3M Non-iD Passive Transmitter Specifications Mode can display a fault resistance up to 10M ΩEnvironmental and Regulatory Specifications Rechargeable Battery InformationRev G Electrical Markets Division Important Notice