3M 2573, 2550 manual Passive Frequencies, Auxiliary Frequencies

Page 34

•Press Cable/Pipe[SK]

•Press Freq [SK]

•Press Power [SK Toggle] until the desired frequency is displayed: (“Power” 60, 60L, 60H, or 120).

•Press Menu/OK [5] to return to Locate mode.

All U.S. receivers default to 60 Hz.

To set the receiver to detect 50 Hz signals refer to 5.D. Enabling/Disabling Locating Frequencies section of this manual.

C. Passive Frequencies

The receiver (without a 3M™ Dynatel™ Transmitter 2500 Series) can be used to detect some CATV cables (31.5 kHz). (A horizontal-scan television NTSC must be turned on to generate this frequency.)

•Press Menu/OK [5] (you may have to press Menu/OK [5] twice to toggle to the LOCATE MENU display).

•Press Cable/Pipe [SK]

•Press Freq [SK]

•Press Pasv [SK Toggle]

•Press Menu/OK [5] to return to Locate mode.

D. Auxiliary Frequencies

Auxiliary frequencies are signals generated from remote location transmitters, or frequency generating transmitters.

•Press Menu/OK [5] (you may have to press Menu/OK [5]twice to toggle to the LOCATE MENU display).

•Press Cable/Pipe [SK]

•Press Freq [SK]

•Press Aux [SK Toggle] until the desired frequency is displayed; (“Aux” 512, 560, 333 Hz, or user defined frequencies).

•Press Menu/OK [5] to return to Locate mode.

34	78-9000-0192-2 Rev C

Image 34

Contents 3M Dynatel Cable/Pipe/Fault Locator 2550/2573 Series Contents Aerial Faults Toning Cable Identification Rev C Safety Information Intended UseAbout This Manual Transmitter Battery Installation Quick StartReceiver Battery Installation Service and Accessories Cleaning Receiver and Transmitter UnitsTransmitter 2550 Keypad and Connector Definitions Transmitter 2573Keypad and Connector Definitions Rechargeable Battery Information Maximum Transmitter OutputReceiver 2550 Keypad and Display Definitions Rubber coverReceiver Keypad and Display Definitions ReceiverMain Menu/Locate Menu Menu DisplaysMain Menu Display Main Menu Display Rev C Selecting Depth Units Configuring The ReceiverSetting the Receiver Clock Selecting a LanguageEnabling/Disabling Locating Frequencies Selecting Locate Modes Antenna ModesSelecting External Jack Frequencies Tone Frequencies Creating User Defined FrequenciesSelecting Locating Audio Adjusting Display ContrastMenu/OK 5Toggle to Main Menu + More SK4 + SK5 + SKc Transmitter Connections Locating Buried Cables And PipesDirect Connect Method Rev C 3M Dyna-Coupler Method Non-SweepingPassive Induction Mode Locating Induction MethodSweeping Active Induction Mode Locating Passive SweepsOne-person Active Induction Mode Sweeps Two-person Active Induction Mode Sweeps Transmitter Set-upReceiver Locating Trace Modes Trace View T-ViewSpecial Peak Spl Pk Induction Peak Ind PkDirectional Peak Dir Pk Left of Target Path Directly Over Target PathDirectional Null DirNull Depth and Current Estimate Expanded ModeVOL 13 press up arrow Locating Frequencies Power FrequenciesActive Frequencies Passive Frequencies Auxiliary FrequenciesLocating in Directional Peak Mode Rev C Locating Active Duct Probes Sondes Determining Active Duct Probe Depth Locating Buried Sheath Faults And Earth Return Faults Transmitter SetupPinpointing the Buried Fault Rev C Locating 3M Electronic Markers and 3M iD Markers Alert ModeEnabling/Disabling Marker Types Single Marker Locate Dual Marker Locate 3M iD Marker DepthPassive Electronic Marker Non-iD Depth Creating/Editing Templates for 3M iD Markers Creating New TemplatesRev C Rev C Editing Templates Menu/OK 5Toggle to Main Menu + Write Mode SK11 Writing 3M iD MarkersRev C Press Menu/OK 5Toggle to Main Menu + Write Mode SK1 Modifying Marker Data to be WrittenRev C Rev C Reviewing Marker Read/Write History Reading 3M iD MarkersRead History Write History SK Capturing the GPS Coordinates Capture Mode / ModeGPS Compatibility Operation Menu/OK 5Toggle to Main Menu + SK3 + NmeaPath Mapping with GPS Menu/OK 5Toggle to Main Menu + SK3 + GISCreating Trace Templates Menu/OK 5Toggle to Main Menu + SK3 + GIS SK or PDA SKTransmitter Setup Additional ApplicationsTransmitter Setup Connection DiagramsCable Identification Receiver Setup Help ModeMenu/OK 5Toggle to Main Menu + More SK4 + SK7 Self Test of Receiver Dynatel PC Tool Kit and Locator Software UpgradesMenu/OK 5Toggle to Main Menu + More SK4 + S/N# SK6 Standard Configurations Product Description And Optional AccessoriesProduct Description Locator Coupler Accessory Kit, 6 150 mm 1196/C Optional 3M Accessories for 3M Dynatel LocatorsLocator Coupler Accessory Kit, 4.5 114 mm 4519 2876Receiver Specifications SpecificationDetection Depth 3M Non-iD Passive Watt Transmitter Specifications Meter mode can display a fault resistance up to 10M ΩEnvironmental and Regulatory Specifications Rechargeable Battery InformationRev C Electrical Markets Division Important Notice