3M 2550, 2573 manual Path Mapping with GPS, Menu/OK 5Toggle to Main Menu + SK3 + GIS

Page 57

B. Sending 3MiD Marker Data to GPS (Capture-Transmit Mode / Mode 2)

Menu/OK [5:Toggle to MAIN MENU] + [SK:3] + GIS

Receivers that have marker locating capability (indicated by ‘iD’ in the model number) can be configured to send 3MiD Marker data directly to some GPS devices. When an iD marker is located and read, the information read from the iD marker with feature and attribute data is sent to the GPS device and is stamped with latitude, longitude and date/time data. The data acquired during this logging process can be uploaded to GIS mapping software. For more information and detailed instructions pertaining to specific GPS devices, refer to www.3M.com/dynatel for GPS instruction sheet.

C. Path Mapping with GPS

The 3M DynatelCable and Pipe Locators 2500 Series are compatible with hand- held GPS devices and now have the ability to map the path of underground target facilities. While measuring the depth to the target, the technician can automatically log the coordinates of the path to the GPS device. These logged points contain the Trace template that can have valuable information regarding the facility (owner, utility, size, etc.) and the method used to find the path (frequency, current, and measured depth).

In order to transmit the path information to a GPS device, the GPS device has to have the ability to accept information on one of its com ports at 4800 Baud. Using the manual supplied with the GPS device, configure the com port of the GPS device to communicate with the receiver.

If ArcPadsoftwae is the mapping software on the mobile device, download the 3M software application script from the website: www.3M.com/dynatel.

With ArcPadapplication installed, the receiver will send the path information (locate frequency, depth, current, and trace template information) into the software program as a logged point and can be saved as a .shp file.

78-9000-0192-2 Rev C

57

Image 57
Contents 3M Dynatel Cable/Pipe/Fault Locator 2550/2573 Series Contents Aerial Faults Toning Cable Identification Rev C Intended Use Safety InformationAbout This Manual Quick Start Transmitter Battery InstallationReceiver Battery Installation Cleaning Receiver and Transmitter Units Service and AccessoriesTransmitter 2550 Keypad and Connector Definitions Transmitter 2573Keypad and Connector Definitions Maximum Transmitter Output Rechargeable Battery InformationRubber cover Receiver 2550 Keypad and Display DefinitionsReceiver Receiver Keypad and Display DefinitionsMenu Displays Main Menu/Locate MenuMain Menu Display Main Menu Display Rev C Setting the Receiver Clock Configuring The ReceiverSelecting Depth Units Selecting a LanguageSelecting Locate Modes Antenna Modes Enabling/Disabling Locating FrequenciesCreating User Defined Frequencies Selecting External Jack Frequencies Tone FrequenciesAdjusting Display Contrast Selecting Locating AudioMenu/OK 5Toggle to Main Menu + More SK4 + SK5 + SKc Locating Buried Cables And Pipes Transmitter ConnectionsDirect Connect Method Rev C 3M Dyna-Coupler Method Induction Method Non-SweepingPassive Induction Mode LocatingPassive Sweeps Sweeping Active Induction Mode LocatingOne-person Active Induction Mode Sweeps Transmitter Set-up Two-person Active Induction Mode SweepsTrace View T-View Receiver Locating Trace ModesInduction Peak Ind Pk Special Peak Spl PkLeft of Target Path Directly Over Target Path Directional Peak Dir PkDirectional Null DirNull Expanded Mode Depth and Current EstimateVOL 13 press up arrow Power Frequencies Locating FrequenciesActive Frequencies Auxiliary Frequencies Passive FrequenciesLocating in Directional Peak Mode Rev C Locating Active Duct Probes Sondes Determining Active Duct Probe Depth Transmitter Setup Locating Buried Sheath Faults And Earth Return FaultsPinpointing the Buried Fault Rev C Alert Mode Locating 3M Electronic Markers and 3M iD MarkersEnabling/Disabling Marker Types Single Marker Locate 3M iD Marker Depth Dual Marker LocatePassive Electronic Marker Non-iD Depth Creating New Templates Creating/Editing Templates for 3M iD MarkersRev C Rev C Editing Templates Writing 3M iD Markers Menu/OK 5Toggle to Main Menu + Write Mode SK11Rev C Modifying Marker Data to be Written Press Menu/OK 5Toggle to Main Menu + Write Mode SK1Rev C Rev C Reading 3M iD Markers Reviewing Marker Read/Write HistoryRead History GPS Compatibility Operation Capturing the GPS Coordinates Capture Mode / ModeWrite History SK Menu/OK 5Toggle to Main Menu + SK3 + NmeaMenu/OK 5Toggle to Main Menu + SK3 + GIS Path Mapping with GPSMenu/OK 5Toggle to Main Menu + SK3 + GIS SK or PDA SK Creating Trace TemplatesAdditional Applications Transmitter SetupConnection Diagrams Transmitter SetupCable Identification Help Mode Receiver SetupMenu/OK 5Toggle to Main Menu + More SK4 + SK7 Dynatel PC Tool Kit and Locator Software Upgrades Self Test of ReceiverMenu/OK 5Toggle to Main Menu + More SK4 + S/N# SK6 Product Description And Optional Accessories Standard ConfigurationsProduct Description Locator Coupler Accessory Kit, 4.5 114 mm 4519 Optional 3M Accessories for 3M Dynatel LocatorsLocator Coupler Accessory Kit, 6 150 mm 1196/C 2876Specification Receiver SpecificationsDetection Depth 3M Non-iD Passive Meter mode can display a fault resistance up to 10M Ω Watt Transmitter SpecificationsRechargeable Battery Information Environmental and Regulatory SpecificationsRev C Important Notice Electrical Markets Division