Dish Network Duo 322, 123698 manual On-Screen Messages, 112

Page 68

Chapter 4

Reference

On-Screen Messages

This table describes some on-screen messages in the order of their message numbers. Find the message number in the upper right corner of the message displayed on your TV screen, and then find the matching number in this table.

 

 

 

 

 

 

Message Number

Possible Reason

What to Do

 

 

 

 

 

 

 

 

Heavy rain, snow, or cloud cover

Note the local weather conditions. Contact your MDU building

 

 

112

may be interfering with transmission

manager for further information/instructions

 

 

of the satellite signal, or there may

 

 

 

 

be other interference.

 

 

 

 

 

 

 

 

 

The receiver may not yet have been

If you have authorized the receiver, wait a few minutes to see if the

 

 

 

electronically linked with the Smart

message is removed. Make sure that all required cables are in place,

 

 

 

Card, via the satellite signal. The

and check that all cable connections are tight and dry (for outdoor

 

 

005

satellite dish may have moved so

cables).

 

 

that it is no longer picking up the

Check that the Signal Strength bar in the QAM/Signal menu is

 

 

 

satellite signal. The cable

green and displays the word Locked. If not, contact your MDU

 

 

 

connections may have loosened or

building manager. If you have not authorized the receiver, call the

 

 

 

have moisture inside. There may be

Commercial Customer Service Center for help.

 

 

 

an interruption of the satellite signal.

 

 

 

 

 

 

 

 

 

The receiver may not be connected

You must connect the receiver to an active telephone connection at

 

 

006

to an active telephone line.

all times. If you install two or more receivers, you must connect

 

 

The Smart Card credit limit may

each receiver to an active telephone connection at all times.

 

 

 

have been suspended.

Review your pay per view purchases to check the Smart Card credit

 

 

 

 

limit.

 

 

 

 

 

 

 

008

Phone signal not working correctly.

If connected with DSL phone line, install a DSL filter between the

 

 

 

receiver and the telephone wall jack. You can obtain the filter from

 

 

 

 

your DSL provider.

 

 

 

 

 

 

 

 

Viewers in specific areas are

Remember that the program providers specify which programs

 

 

 

prohibited from watching certain

are “blacked out” for which viewers, not DISH Network.

 

 

 

programs.

 

 

 

011, 012

For example, viewers who live close

 

 

 

to a particular football stadium may

 

 

 

 

be prohibited from watching football

 

 

 

 

games that are played in that

 

 

 

 

stadium.

 

 

 

 

 

 

 

 

013, 014

You may have tried to tune to a

You must buy a channel before you can tune to a program on that

 

 

program on a channel which you

channel. Call the Customer Service Center to buy the channel, or if

 

 

 

have not bought.

you believe this message was displayed by mistake.

 

 

 

 

 

 

 

 

You may have just plugged in the

Wait a few minutes to see if the message is removed. Make sure that

 

 

 

receiver, and it is acquiring the

all required cables are in place, and check that all cable connections

 

 

015

satellite signal. Or, the receiver may

are tight and dry (for outdoor cables).

 

 

have temporarily lost the signal.

Check that the Signal Strength bar in the QAM/Signal menu is

 

 

 

 

green and displays the word Locked. If not, contact your MDU

 

 

 

 

building manager.

 

 

 

 

 

 

 

 

The receiver may not be connected

You must connect the receiver to an active telephone connection at

 

 

 

to an active telephone line.

all times. If you install two or more receivers, you must connect

 

 

018

The Smart Card credit limit may

each receiver to an active telephone connection at all times.

 

 

have been exceeded.

Review your pay per view purchases to check the Smart Card credit

 

 

 

 

limit.

 

 

 

 

Call the Customer Service Center for help checking the credit limit,

 

 

 

 

and/or to get authorization to make a purchase.

 

 

 

 

 

 

 

 

The receiver may not yet have been

If you have authorized the receiver, wait a few minutes to see if the

 

 

 

electronically linked with the Smart

message is removed. Make sure that all required cables are in place,

 

 

 

Card, via the satellite signal. The

and check that all cable connections are tight and dry (for outdoor

 

 

022

satellite dish may have moved so

cables).

 

 

that it is no longer picking up the

Check that the Signal Strength bar in the QAM/Signal menu is

 

 

 

satellite signal. The cable

 

 

 

green and displays the word Locked. If not, contact your MDU

 

 

 

connections may have loosened or

 

 

 

building manager.

 

 

 

have moisture inside. There may be

 

 

 

 

 

 

 

an interruption of the satellite signal.

 

 

 

 

 

 

 

Page 64

Image 68
Contents Contents Contents Safety Instructions Safety Tips Welcome to Dish NetworkTM OverviewInformation TipsOrdering Your Programming If You Need More AssistanceQuick Start Guide Finding Programs To Watch Quick Start GuideQuick Tour of the Menus Quick Tour of the Menus Chapter About Satellite Television About MDUChapter Power Button and Light Receiver Front PanelSmart Card Door Up and Down Arrow ButtonsReceiver Back Panel Connections Telephone Jack Remote ControlRemote Control Remote Control Batteries On Screen Low Remote Battery WarningRemote Control Settings Remote Control SettingsChecking the Remote Control Address Change the AddressTypical Connection Procedure Connecting Your ReceiverConnection Diagram Example Performing the QAM Frequency Scan Performing the QAM Frequency ScanChapter Strength screen LockedChapter Select the Installation and Setup option Connecting Your Receiver to a Phone LineConnecting Your Receiver to a Phone Line Chapter Using the Remote Control Volume Button Guide ButtonArrow Buttons Select ButtonCancel Button TV/Video ButtonRecord Button Number Pad ButtonsUsing the Menus Recover ButtonChanging Channels Favorites ListOpening the Menus Closing the MenusMenu Options Highlighting a Menu OptionSelecting a Choice in a Menu List Canceling a ProcedureHighlighting a Choice in a Menu List Favorites Lists, see Using the Program GuideUsing the Program Guide Opening the Program Guide Selecting a Program in the Program GuideUsing the Browse Banner Using the Browse BannerUsing the Program Banner Closing The Program GuideChapter Cancel option Ordering Pay Per View ProgramsOrdering Pay Per View Programs Program GuideUsing Themes ThemesDish Home Interactive TV Applications Using Favorites ListsDish Home Interactive TV Applications Creating or Changing a Favorites List ListChanging the Name of a Favorites List Using Favorites ListsMaking a Favorites List Active Event Timer Frequencies Using TimersEvent Timer Types Before an Event Timer Operates Setting Up an Automatic Event TimerUsing Timers Browse Banner, Themes Menu or the Program GuideSelect the Create option to save the event timer Setting Up a Manual Event TimerOverlapping Event Timers Quick RecordMaximum Number of Event Timers Editing an Event TimerDeleting an Event Timer Special Consideration When Using Event TimersSetting Up the Receiver to Control a VCR Event Timer Performance when the Receiver is OffSetting Up a VCR for VCR Timers Using LocksSetting Up a VCR for VCR Timers How to Set Locks a Two Step ProcessWhen You Have Locked the Receiver Locking and Unlocking the ReceiverCreating or Changing Rating Content Code Locks Using LocksChapter Creating or Changing Channel Locks Locking or Unlocking the Front Panel Buttons Unlocking or Locking Pay Per View ProgramsHiding and Unhiding Adult Channels Hiding and Unhiding Locked ChannelsUnhide Lock option Changing the Receiver PasswordPersonal Identification Number Caller ID Screens Using Caller IDUsing Caller ID Resetting to Factory Defaults To Turn the Caller ID On and OffRemote Control Modes System Setup menuChanging Program Languages Control Other Devices with the RemoteLimited Mode Set Up the Remote ControlScan for Device Codes Control Other Devices with the RemoteTV Mode Button Power ButtonCheck the Device Codes Control a TV or a Second TVControl Other Devices with the Remote Control a VCR or a DVD PlayerNumber Pad Buttons VCR/DVD ButtonsUp and Page Down Buttons Switching Between TV and Device Volume Control AUX Mode ButtonTo set the remote to control the device’s volume Control a Tuner or AmplifierTo set the remote back to control the TV volume Testing the System Testing the SystemStarting a Test Telephone Connection TestChapter Troubleshooting Tables ReferenceOn-Screen Messages 112Using the Remote Control Troubleshooting TablesUsing the Menus Using the Program Guide or the Browse BannerHearing a Program Watching a ProgramChanging Channels Using LocksUsing Favorite Lists Using the Telephone for Voice/Data/FAX Buying a Pay Per View ProgramTroubleshooting Tables Using Event TimersDevice Codes TV CodesVCR Codes MGAITT Tuner/Amplifier Codes TV/VCR ComboDVD Player Codes DVD/VCR Combo TV/DVD Combo CodesIndex Index Index Index Index Index What the Warranty Does Not Cover Limited WarrantyWhat the Warranty Covers Legal Limitations If You Need AssistancePost Receipt Exchange Program Accessory WarrantyAdvance Exchange Program Feedback@echostar.com Dish Network Customer Service Center Box Northglenn, COResidential Customer Agreement Residential Customer Agreement Billing Policies and Payments for Services Cancellation of Service Equipment Transfer of ACCOUNT, Services or Equipment Telephone Communication Staying LegalFCC Compliance Radio Interference Appendix 123698