Kathrein CAP 600 manual Figure E

Page 15

INSTALLATION AND CONNECTION

Figure: E

Direction of travel

Gasket with plug for

the unused duct

Battery, ignition

Receiver

Lift up the turntable and place it carefully on the mounting plate facing in the direction of travel (see illustration Fig. E) (do not step on the plug connector and do not kink/crush the cables!).

The through holes on the turntable must be perfectly aligned with the threaded holes on the mounting plate. When lowering, make sure that the cables are fed through the cable gland and are not crushed.

Apply a little adhesive sealant to the six threaded holes in the mounting plate and screw the fastening screws into the thread. Tighten the screws to a torque of 6 Nm.

To prevent water vapour from inside the vehicle reaching the turntable through the roof gland, thread the two cables through the sealing gasket supplied (see Fig. E) and insert this into the roof gland until it reaches the stop. Insert the plug into the third cable duct which is not used. Make sure that no tensile loads are acting downwards on the sealing gasket as this can cause it to fall out over time.

15

Image 15
Contents CAP Contents Foreign Language Installation MANUAL/DISPOSAL Disposal InstructionsUsed batteries are special waste Product Package Mobiset 2 CAP 600 COMPONENTS/SCOPE of DeliveryProper USE USE for the Intended Purpose Proper USESafety Instructions Important Notes Fundamental informationAdhesive sealant Road Traffic Licensing Regulations StVZO Power supply, fusingChecks before commencing a journey Unpacking and Preparation Installation and ConnectionSelecting the Installation Location Required Tools and EquipmentDirection of travel Installation Steps Installation and Connection Installation and Connection Installation of Turntable Figure E Version with External Cable Gland FIG. F Brief Instructions for Installing the Turntable Tightening torque 6 Nm Suspended Installation Installation on a Fixed Flat Surface Reversal is not possible unit will not function Installation and Connection Connection Example for 12 V Battery Connection Reception RANGE/FOOTPRINT Dismantling Address of the Service CentreDismantling for Servicing ESCPolarisation Setting Polarisation SettingSafety Notes On the Turntable Installation ProcessMiddle standard View after installation +15Manual Lowering to Park Position Manual Lowering Dimensions MM Technical DataTechnical Data LNB Type CAPPotential hazards Sikaflex 291 Safety Data SheetMaterials/preparation and company designation Composition/data on componentsExposure limitation and personal protective equipment Measures for fire fightingMeasures if inadvertently released Handling and storageStability and reactivity Physical and chemical characteristicsTransport data Toxicology data SensitisationEcological data Disposal instructionsOther data Sikaflex-291 Aflex Sikaflex 291 Technical Data SheetChemical Stability CAP 600 Operating Manual Remote Control Important Information for CAP 600 Before SetupFirst Installation TV-SCART-Output Picture formatLocal time offset SystemAlignment Satellite Search Manual Correction Channel Selection from the Channel List Channel Satellite SelectionTimer Programming Change of LOCATION/TIMER ProgrammingResetting the Motorised Antenna RESET/PARKINGParking the Turntable System Protection Messages Special Messages from the TurntableSpecial Messages from the Turntable Messages Arising from Software Problems Further Messages EC Declaration of Conformity Declaration of ConformityFor Your Notes For Your Notes 936.3220/-/0907/ZWT Technical data subject to change
Related manuals
Manual 1 pages 4.49 Kb

CAP 600 specifications

The Kathrein CAP 600 is a cutting-edge solution designed for the modern telecommunications landscape, catering primarily to the demands of mobile network operators and service providers. This compact, high-performance active antenna system is engineered to enhance connectivity in urban environments, significantly improving network efficiency and user experience.

One of the key features of the Kathrein CAP 600 is its multi-band capability. It supports various frequency bands including LTE, 5G NR, and others, making it versatile for both current and future network deployments. This allows operators to seamlessly upgrade their services without needing to overhaul their infrastructure.

The CAP 600 is equipped with advanced MIMO (Multiple Input Multiple Output) technology, which leverages multiple antennas at both transmitting and receiving ends to boost data throughput and reliability. This technology is essential for maximizing spectral efficiency, thus accommodating more users and higher data rates in dense urban areas.

In terms of design, the Kathrein CAP 600 features a compact and lightweight structure. This is crucial for installations in constrained environments where space is at a premium. The antenna's sleek aesthetics also allow it to blend into its surroundings, thereby reducing visual impact, which is often a concern in urban deployments.

The antenna incorporates intelligent software features that facilitate dynamic beamforming. This enables targeted coverage, allowing signals to be directed towards users rather than being broadcast in all directions, thus minimizing interference and optimizing network performance. Additionally, the built-in remote management capabilities allow operators to monitor and manage network performance in real-time, enhancing operational efficiency.

Regarding sustainability, the CAP 600 is designed with energy efficiency in mind. The use of advanced materials and optimized hardware contributes to lower energy consumption, making it an environmentally friendly choice for operators looking to reduce their carbon footprint.

Overall, the Kathrein CAP 600 is a sophisticated solution that meets the high demands of modern mobile networks. With its advanced features, technologies, and commitment to sustainable operations, it represents a pivotal component for any operator looking to enhance connectivity and provide exceptional service in today’s dynamic telecommunications environment.