Reversal is not possible unit will not function

Kathrein CAP 600 manual Reversal is not possible unit will not function

INSTALLATION AND CONNECTION

LAYING CABLES AND CONNECTING THE TURNTABLE

•Lay the coaxial cable to the UFS 740sw.

•Lay the turntable power supply cable (3-pin plug) to the battery.

Avoid laying the cables across sharp edges and secure the cables against possible chaﬁng points.

•Connect the coaxial cable (coming from the turntable) to the “IF IN” F socket on the rear of the UFS 740sw.

•Place the infrared sensor for the receiver close to or directly on top of the TV set and lay the cable to the UFS 740sw. Connect the 6-pin Western connector at the rear to the socket marked “IR REMOTE IN”.

Note: Lay the AV cinch enclosed with the CAP 600 to the Scart cable. Take great care to plug the cables into the correct sockets! The cinch connector must be assigned to the UFS 740sw and the Scart connector to the TV set.

Reversal is not possible - unit will not function!

CONNECTING TO THE UFS 740SW

Isolate the on-board power supply (master switch “off” or disconnect negative pole of on-board power supply battery) before commencing the following work:

•Connect the power cable supplied (depending on the power supply available in your motor home or

caravan, either a 12 V supply or a 230 V supply via a power supply unit) to the “” socket on the receiver.

Make sure that the “inline” integrated fuse (5 A) of the cable is fully plugged in and is intact. If the fuse blows, the source of the fault must ﬁrst be eliminated. The fuse must only ever be replaced by a fuse with the same rating (5 A).

The fuses in the cable and in the receiver may never be bridged – cable ﬁre hazard!

•At the connecting point for the power cable, the voltage must not fall below 10.9 V even with a load of 12 A. Otherwise optimum functioning can no longer be guaranteed.

•Connect the power cable to the respective socket in your motor home or caravan (12 V or 230 V).

CAP 600 specifications

The Kathrein CAP 600 is a cutting-edge solution designed for the modern telecommunications landscape, catering primarily to the demands of mobile network operators and service providers. This compact, high-performance active antenna system is engineered to enhance connectivity in urban environments, significantly improving network efficiency and user experience.

One of the key features of the Kathrein CAP 600 is its multi-band capability. It supports various frequency bands including LTE, 5G NR, and others, making it versatile for both current and future network deployments. This allows operators to seamlessly upgrade their services without needing to overhaul their infrastructure.

The CAP 600 is equipped with advanced MIMO (Multiple Input Multiple Output) technology, which leverages multiple antennas at both transmitting and receiving ends to boost data throughput and reliability. This technology is essential for maximizing spectral efficiency, thus accommodating more users and higher data rates in dense urban areas.

In terms of design, the Kathrein CAP 600 features a compact and lightweight structure. This is crucial for installations in constrained environments where space is at a premium. The antenna's sleek aesthetics also allow it to blend into its surroundings, thereby reducing visual impact, which is often a concern in urban deployments.

The antenna incorporates intelligent software features that facilitate dynamic beamforming. This enables targeted coverage, allowing signals to be directed towards users rather than being broadcast in all directions, thus minimizing interference and optimizing network performance. Additionally, the built-in remote management capabilities allow operators to monitor and manage network performance in real-time, enhancing operational efficiency.

Regarding sustainability, the CAP 600 is designed with energy efficiency in mind. The use of advanced materials and optimized hardware contributes to lower energy consumption, making it an environmentally friendly choice for operators looking to reduce their carbon footprint.

Overall, the Kathrein CAP 600 is a sophisticated solution that meets the high demands of modern mobile networks. With its advanced features, technologies, and commitment to sustainable operations, it represents a pivotal component for any operator looking to enhance connectivity and provide exceptional service in today’s dynamic telecommunications environment.