IBM 3531 manual Installing the EXP300 in a Tower, Statement

Page 37

Statement 4

≥18 kg (37 lbs)

≥32 kg (70.5 lbs)

≥55 kg (121.2 lbs)

CAUTION:

Use safe practices when lifting.

7.Slide the expansion unit into the rack, and insert the M6 screws Þ Ý. Do not overtighten the M6 Þ Ý screws.

8.Tighten the rear screws Þ Ý.

9.Verify that option switches 1 and 2 (inside the switch card) are set to off (see “Setting the interface options and ID settings” on page 10 for more information).

10.Install hard disk drives and power supplies in the EXP300 expansion unit according to “Locations” on page 8; then, return here to complete the installation.

11.Continue with “Completing the installation” on page 35.

Installing the EXP300 in a Tower

The IBM® Netfinity® EXP300 Rack-to-Tower Conversion Kit converts the EXP300 storage expansion unit into a tower mounted installation. You will need a flat-blade screwdriver and a phillips screwdriver to install the EXP300. Use the mounting hardware that comes with your unit to secure it in the enclosure.

Before installing the expansion unit you must:

Netfinity EXP300 Type 3531 29

Image 37
Contents Ff X pypi Page Ff X pypi Page About this manual Important safety informationOnline support Contents Page Netfinity EXP300 Type FeaturesGeneral Clustering supportDisk drive storage Problem Reference Diagnostics and Test InformationTurning on the expansion unit Turning off the expansion unit Turning off the expansion unit in an emergency Operating specificationsTurning on the expansion unit after an emergency System-management software support Symptom-to-FRU index Locations Getting started Preparing the expansion unit Use safe practices when liftingRemoving CRUs StatementExternal option switches Setting the interface options and ID settingsInternal option switches Option switch 1 Power-control switchUnit ID dial switch Hot-swap drive bays Netfinity EXP300 baysBridge card bay Important information for IBM ServeRAIDSwitch card bay ESM and power supply baysHot-swap power supply/fan bays Hot-swap ESM baysPower-on LED green Front controls, indicators, and devicesPower-supply controls, indicators, connectors Rear controls, indicators, and connectorsESM board user controls Working with hot-swap drives LED State Description Installing hot-swap drivesHard disk drives ServeRAID information Replacing hot-swap drives Removing a hot-swap power supply/fan unit Working with hot-swap powerWorking with cards and boards Installing a hot-swap power supply / fan unitReplacing a bridge card Installing a bridge card Replacing the switch cardRemoving the switch card Removing a bridge cardReplacing an ESM board Conversion of EXP300 to a tower or from a tower Installing the EXP300 in a rack Netfinity EXP300 Type 3531 IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual Installing the EXP300 in a Tower Statement Installing identification labels Serial number label Scsi ID label Expansion unit ID label Installing the EXP300 in a NetBAY enclosure FrontRear Completing the installation Cabling the expansion unit Index System Netfinity EXP300 Type FRU No Parts Listing SystemOptions Power Cords IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual General safety Safety informationElectrical safety Safety inspection guide Handling electrostatic discharge-sensitive devices Grounding requirements Safety notices multi-lingual translationsDo not Statement ≥18 kg 37 lbs ≥32 kg 70.5 lbs ≥55 kg 121.2 lbs IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual Perigo ImportanteCuidado Para Conectar Para DesconectarAo levantar a máquina, faça-o com segurança Instrução IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual Related service information IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual Related service information IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual Related service information IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual Related service information IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual Related service information Connexion Déconnexion Related service information IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual Vorsicht WichtigAchtung Kabel anschlieβen Kabel lösenVorsicht Achtung Pericolo Attenzione Per collegare Per scollegarePericolo Attenzione Related service information IBM Netfinity EXP300 Type 3531 Hardware Maintenance Manual Related service information Peligro Apáguelo Para la conexin Para la desconexiínPeligro Precaución Send us your comments Problem determination tipsThank you for your response Trademarks IBM Page Part Number 06P8514