Polk Audio DP-1 manual Teaching Method

Page 33

PROGRAMMING THE REMOTE

Teaching Method

From time to time the three-digit programming method doesn’t automatically program in all of the commands of the original remote. In such cases you can “teach” the DR-3 individual commands from your original equipment remote control. New commands can be taught to any button except the eight Source/Device buttons at the top of the remote and the LIGHT, MACRO, LEARN, CODE, SAVE, CNCL, MUTE, SURROUND MODE, VOL UP, VOL DOWN, SUB+, SUB– and SYSTEM POWER buttons.

The remote control provides visual feedback via the status light that is located at the top left of the remote control, and the Source/Device buttons. The status light glows in three colors (red, orange and green). These lights will assist you in programming in the learning section of the remote control.

NOTE: You have 20 seconds to perform each step. If the source button light goes off, you need to back up a step and do it again. You can exit the learning mode by pressing the CNCL (cancel) button at any time in the process.

Quick Instructions

Place the DR-3 remote and the original remote controls on a table pointing toward each other as shown in the illustration.

1.Press LEARN for two seconds

2.Select device type with source buttons

3.Push button to be taught on the DR-3

4.Push and hold the button on other remote

5.Wait for green light

6.Release button & press/hold it again until green light blinks, release

7.Repeat steps 3 - 6 for other buttons

8.Press SAVE

Start from the beginning for each device.

Detailed Instructions

Place the DR-3 remote and the original remote controls on a table pointing towards each other as shown in the illustration.

1.Press and hold the LEARN button on the DR-3 for two seconds. The status light at the top left of the remote will glow orange.

2.Select the Source/Device mode in which you would like to teach the new command. The Source/Device button will light up. For example if you wanted to teach a command to the MENU button in the DSS mode on the remote, you would select the DSS Source/Device button and then continue the instructions below to teach the new command to the MENU button.

3.Press the button on the DR-3 that is to be taught the new com- mand. The orange status light will begin to flash continuously. The Source/Device light will turn off.

4.On the source remote control (original equipment remote control), press and hold the button for the command to be learned until the status light on the DR-3 remote turns green.

5.Release the button on the source remote control.

2

1

8

6.Press the button on the source remote control once again to verify that the new command has been learned correctly. The status light on the DR-3 will flash green twice and then turn to a steady orange color to indicate that the programming was successful. The Source/Device button will light.

7.Repeat Steps 3 through 6 for any other buttons to be taught in the device mode selected in Step 2.

8.Press and hold the SAVE button for two seconds to save the programmed information. The orange status light flashes twice. The Source/Device button light will turn off.

www.polkaudio.com

9

Image 33
Contents DP-1 Important Safety Instructions Please read the following carefully PrecautionsWord from Matthew Polk Connecting the DP-1 Basic SetupGetting Started Remote Controls These buttons serve two DR-3 Remote Guided TourRemote Controls Push this button once to pause playing How to navigate and select choices DP-1 SET UP MenusSetting Digital Audio Output Sample Frequency Setting DRCMenu Language Options Setting a Rating Parental Block/Password Menus optionalSetting a Password Unlocking the Rating BlockPlaying a DVD DVD OperationAdvanced DVD Operation Graphic User Interface GUI Menus CD Operation Playing a CDAdvanced CD Operation Functions as shown in the chart figure Playing an MP3 CD MP-3 OperationMP3 Notes Advanced MP3 OperationTroubleshooting Guide Troubleshooting Guide Polk Audio Limited Warranty DP-1 SpecificationsDVD Player OutputsPolk Customer Service 800 RM2069-1 DR-3 Programming the Remote IntroductionVOL Stop Page Button Name DR-3 Function ListManual Three-Digit Code Method Programming the RemoteFinding the Three-Digit Code Number for a Device Auto Search MethodTeaching Method To Erase All the Learned Commands One Source/Device Mode Erasing a Learned Command From a ButtonRestoring Factory Programming Erasing All the Learned Commands All Device ModesMacro Operation Programming the Macro ButtonTo Erase a Macro Sequence Macro Sequence Programming Example Factory ResetManufacturer/Brand Set-Up Code Number Setup CodesVCR Aiwa Manufacturer/Brand Set-Up Code Cable TV Set-Up CodeManufacturer/Brand Set-Up CodeRM2070-1 Page Page