Polk Audio DP-1 manual Erasing a Learned Command From a Button

Page 34

 

 

PROGRAMMING THE REMOTE

 

 

 

 

 

 

 

Erasing a Learned Command From a Button

 

 

 

 

 

 

 

NOTE: You have 20 seconds to perform each step. If the source button

 

 

 

 

 

 

 

light goes off, you need to back up a step and do it again. You can exit

 

 

 

 

 

 

 

by pressing the CNCL (cancel) button at any time in the process.

 

 

 

 

 

 

 

1.

Press and hold the LEARN button for two seconds.

 

 

 

 

 

 

 

 

 

The status light at the top left of the remote will glow orange.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Press the Source/Device associated with the button you wish

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to erase. The Source/Device button light will turn on.

4

 

 

 

 

 

 

3.

Press the button that is to be erased. The orange status light will

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

flash continuously and the Source/Device button will turn off.

 

 

 

 

 

 

 

4.

Press the LIGHT button. The status light will flash twice, then

 

 

 

 

 

 

 

 

 

turn to a steady orange. The Source/Device button will turn on.

 

 

 

 

 

 

 

5.

Repeat from Step 3 for any other buttons to be erased in the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

selected device mode.

 

 

 

 

 

 

 

6.

To save your changes, press the SAVE button. The orange status

 

 

 

 

 

 

 

 

 

light will flash twice and then turn off. The Source/Device button

 

 

 

 

 

 

 

 

 

will turn off.

 

 

 

 

 

 

 

6 1

To Erase All the Learned Commands

in One Source/Device Mode:

NOTE: You have 20 seconds to perform each step. If the source button light goes off, you need to back up a step and do it again. You can exit by pressing the CNCL (cancel) button at any time in the process.

1.Press and hold the LEARN button for two seconds.

The status light at the top left of the remote will glow orange.

2.Press the Source/Device button you wish to erase. The Source/Device button light will turn on.

3.Press and hold the LIGHT button for 5 seconds until the status light flashes red five times and then flashes green twice and the Source/Device button turns off. The status light will go to a constant orange indicating that all the learned information on buttons in the Source/Device mode have been erased. The Source/Device button will turn on.

4.To save your changes, press the SAVE button. The orange status light will flash twice and then turn off. The Source/Device button will turn off.

2

3

4 1

10

Polk Customer Service (800) 377-7655

Image 34
Contents DP-1 Important Safety Instructions Precautions Please read the following carefullyWord from Matthew Polk Basic Setup Connecting the DP-1Getting Started Remote Controls DR-3 Remote Guided Tour These buttons serve twoRemote Controls Push this button once to pause playing DP-1 SET UP Menus How to navigate and select choicesSetting DRC Setting Digital Audio Output Sample FrequencyMenu Language Options Setting a Password Parental Block/Password Menus optionalSetting a Rating Unlocking the Rating BlockDVD Operation Playing a DVDAdvanced DVD Operation Graphic User Interface GUI Menus Playing a CD CD OperationAdvanced CD Operation Functions as shown in the chart figure MP-3 Operation Playing an MP3 CDAdvanced MP3 Operation MP3 NotesTroubleshooting Guide Troubleshooting Guide DVD Player DP-1 SpecificationsPolk Audio Limited Warranty OutputsPolk Customer Service 800 RM2069-1 DR-3 Introduction Programming the RemoteVOL Stop Page DR-3 Function List Button NameProgramming the Remote Manual Three-Digit Code MethodAuto Search Method Finding the Three-Digit Code Number for a DeviceTeaching Method Erasing a Learned Command From a Button To Erase All the Learned Commands One Source/Device ModeErasing All the Learned Commands All Device Modes Restoring Factory ProgrammingProgramming the Macro Button Macro OperationTo Erase a Macro Sequence Factory Reset Macro Sequence Programming ExampleSetup Codes Manufacturer/Brand Set-Up Code NumberVCR Aiwa Set-Up Code Manufacturer/Brand Set-Up Code Cable TVSet-Up Code Manufacturer/BrandRM2070-1 Page Page