Polk Audio DP-1 manual Programming the Remote, Manual Three-Digit Code Method

Page 31

PROGRAMMING THE REMOTE

Manual Three-Digit Code Method

The DR-3 remote control can duplicate the remote functions of most brands of audio/video equipment by simply entering in a three-digit code number. When you enter in the code the DR-3 “learns” most or all of the remote functions of that equipment so you don’t need to program the DR-3 button by button. There are tables on pages 14 - 15 that list the major audio/video brands and their three-digit remote codes.

Quick Instructions

4

1. Look up code number

2. Turn on equipment

3. Press and hold CODE until the Status Light glows red

4. Press Source/Device button

5. Enter code number

6. Press SAVE

Detailed Instructions

1. Look up the type and brand of equipment you wish to duplicate in the tables that appear on pages 14 - 15 in this manual. For exam-

ple, if you wish to program the DR-3 to operate a Panasonic VCR,

go to the VCR chart on page 15 and find the code(s) for Panasonic.5 It might be a good idea to jot that number down on this page so you

have it handy as you move through the programming steps.

Note: If there is more than one three-digit number listed for your

brand, try one code number at a time until your equipment turns3 off after the last step in the programming process. When your

equipment turns off, you have selected the right code. You can also verify that you have programmed the correct three-digit number by pressing the SOURCE POWER button. Your equipment should turn On and Off.

2.Turn on the equipment you wish to program.

NOTE: From here on in you have 20 seconds to perform each step. If the Source/Device button light goes off, you need to back up a step and do it again. You can exit the set-up mode by pressing the CNCL (cancel) button at any time in the process.

3.Press and hold the CODE button for two seconds. The red status light at the top left of the remote will turn on.

4.Press the Source/Device button you wish to program (e.g. VCR, DVD, etc.). The Source button will light up. In the case of the Panasonic VCR example, you would push the VCR Source button.

5.Point the Polk DR-3 remote control toward the equipment and enter the first listed three-digit code number of your brand of equipment. The Status light and the Source/Device button will blink once for each button pressed. The equipment will turn off when you enter the correct three-digit number.

6.Press and hold the SAVE button for 2 seconds to store the three- digit number. The Status light and the Source/Device button light will blink twice to confirm that the code has been stored, and then turn off.

7.Try all the functions on the remote control.

NOTE: If any of the functions do not work as they should, repeat the programming process using the next three-digit code number assigned to your brand. If only one or two buttons don’t work right, it may be easier to individually “teach” the DR-3 those commands (see page 9) or use the Auto Search method (see page 8) rather than trying all the three-digit codes.

6

www.polkaudio.com

7

Image 31
Contents DP-1 Important Safety Instructions Please read the following carefully PrecautionsWord from Matthew Polk Basic Setup Connecting the DP-1Getting Started Remote Controls These buttons serve two DR-3 Remote Guided TourRemote Controls Push this button once to pause playing How to navigate and select choices DP-1 SET UP MenusSetting DRC Setting Digital Audio Output Sample FrequencyMenu Language Options Unlocking the Rating Block Parental Block/Password Menus optionalSetting a Rating Setting a PasswordPlaying a DVD DVD OperationAdvanced DVD Operation Graphic User Interface GUI Menus Playing a CD CD OperationAdvanced CD Operation Functions as shown in the chart figure Playing an MP3 CD MP-3 OperationMP3 Notes Advanced MP3 OperationTroubleshooting Guide Troubleshooting Guide Outputs DP-1 SpecificationsPolk Audio Limited Warranty DVD PlayerPolk Customer Service 800 RM2069-1 DR-3 Programming the Remote IntroductionVOL Stop Page Button Name DR-3 Function ListManual Three-Digit Code Method Programming the RemoteFinding the Three-Digit Code Number for a Device Auto Search MethodTeaching Method To Erase All the Learned Commands One Source/Device Mode Erasing a Learned Command From a ButtonRestoring Factory Programming Erasing All the Learned Commands All Device ModesProgramming the Macro Button Macro OperationTo Erase a Macro Sequence Macro Sequence Programming Example Factory ResetManufacturer/Brand Set-Up Code Number Setup CodesVCR Aiwa Manufacturer/Brand Set-Up Code Cable TV Set-Up CodeManufacturer/Brand Set-Up CodeRM2070-1 Page Page