Sony Hong Kong model, Singapore model Operating the Continuous Playback Mode, Mid, Out, Menu/No

Page 16

4-5-1. Operating the Continuous Playback Mode

1.Entering the continuous playback mode

1 Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.) 2 Rotate the AMS knob and display “CPLAY MODE”.

3 Press the YES button to change the display to “CPLAY MID”.

4 When access completes, the display changes to “C = AD = ”. Note : The numbers “ ” displayed show you error rates and ADER.

2.Changing the parts to be played back

1 Press the YES button during continuous playback to change the display as below.

“CPLAY MID” n“CPLAY OUT” n“CPLAY IN”

When pressed another time, the parts to be played back can be moved.

2When access completes, the display changes to “C = AD = ”. Note : The numbers “ ” displayed show you error rates and ADER.

3.Ending the continuous playback mode

1 Press the MENU/NO button. The display will change to “CPLAY MODE”.

2Press the §EJECT button to remove the disc.

Note : The playback start addresses for IN, MID, and OUT are as follows.

IN

40h cluster

MID

300h cluster

OUT

700h cluster

4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check.)

1.Entering the continuous recording mode 1 Set a recordable disc in the unit.

2 Rotate the AMS knob and display “CREC MODE”.

3Press the YES button to change the display to “CREC MID”.

4 When access completes, the display changes to “CREC (

)” and

REC

lights up.

Note : The numbers “ ” displayed shows you the recording position addresses.

2.Changing the parts to be recorded

1 When the YES button is pressed during continuous recording, the display changes as below. “CPLAY MID” n“CPLAY OUT” n“CPLAY IN”

When pressed another time, the parts to be recorded can be changed.

REC

goes off.

2 When access completes, the display changes to “CREC (

)” and

 

 

lights up.

 

REC

Note : The numbers “ ” displayed shows you the recording position addresses.

3. Ending the continuous recording mode

1 Press the MENU/NO button. The display changes to “CREC MODE” and REC goes off.

2Press the § button to remove the disc.

Note 1 : The recording start addresses for IN, MID, and OUT are as follows.

 

IN

40h cluster

 

MID

300h cluster

 

OUT

700h cluster

Note 2

: The

MENU/NO

button can be used to stop recording anytime.

Note 3

: Do not perform continuous recording for long periods of time above 5 minutes.

Note 4

: During continuous recording, be careful not to apply vibration.

4-5-3. Non-Volatile Memory Mode (EEP MODE)

This mode reads and writes the contents of the non-volatile memory.

It is not used in servicing. If set accidentally, press the MENU/NO button immediately to exit it.

– 16 –

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Specifications MDS-JE330SELF-DIAGNOSIS Function Items of Error History Mode Items and Contents Flexible Circuit Board Repairing VarnigTable of Contents DisassemblyDiagrams Exploded ViewsSection Servicing Note JIG for Checking BD Board WaveformIOP TEORecord Precedure Checks Prior to Parts Replacement and Adjustments Forced ResetCriteria for Determination Measure if unsatisfactory REC/PLAYRetry Cause Display Mode Bit BinaryHigher Bits Lower Bits Hexa Details Bit When BinaryHexadecimal Binary Location of Parts and Controls Section GeneralFront Panel Case and Front Panel Section DisassemblySlider CAM Base Unit MBU-5A and BD Board SW Board and Loading Motor M103Section Test Mode Precautions for USE of Test ModeSetting the Test Mode Exiting the Test ModeSelecting the Test Mode GroupOperating the Continuous Playback Mode Non-Volatile Memory Mode EEP ModeMID OUTTest Mode Displays Functions of Other ButtonsMeanings of Other Displays Section Electrical Adjustments Parts Replacement and AdjustmentPrecautions for Checking Laser Diode Emissinon Precautions for USE of Optical PICK- UP KMS-260APrecautions for Adjustments Creating Continuously Recorded DiscTemperature Compensation Offset Check Laser Power CheckChecks Prior to Repairs Specified ValuePlay Checking MO Error Rate Check CD Error Rate CheckFocus Bias Check Self-Recording/playback CheckInitial Setting of Adjustment Value Temperature Compensation Offset AdjutmentLaser Power Adjustment Recording and Displaying the IOP InformationTraverse Adjustment Focus Bias Adjustment Error Rate Check Auto Gain Control Output Level AdjustmentCD Auto Gain Control Output Level Adjustment MO Auto Gain Control Output Level AdjustmentAdjusting Points and Connecting Points Section Diagrams Circuit Boards LocationBlock Diagrams BD Section MDS-JE330Main Section LD-LOVOFor schematic diagrams For printed wiring boardsWaveforms Display SectionPrinted Wiring Board BD Section Semiconductor LocationSchematic Diagram BD 1/2 Section Schematic Diagram BD 2/2 Section Schematic Diagram Main 1/2 Section Schematic Diagram Main 2/2 Section Printed Wiring Board Main Section Printed Wiring Board Panel Section Schematic Diagram Panel Section Printed Wiring Board BD Switch Section Schematic Diagram BD Switch Section IC Block DiagramsBD Section IC101 IC121 CXD2654R IC152 BH6511FS-E2IC381 M5218AL IC441 LB1641 Main section IC301 UDA1341TS/N2IC406 M62016L IC101 RF Amplifier CXA2523AR BD board IC PIN FunctionsPin No Pin Name Function MNT0 FOK MNT1 ShckMNT2 Xbusy MNT3 SlocMvci AsyoAsyi AvddTfdr FfdrFrdr FS4IC501 System Control M30620MC-400FP Main board OPT DEL OPT SEL Mode SEL PB-PREC/PB SDASection Exploded Views Case and Back Panel SectionFront Panel Section 6162Mechanism Section MDM-5A 225 226 206 205Base Unit Section MBU-5A 251 252Section Electrical Parts List ResistorsDisplay Display KEY SW Main PIN, Connector 7P Inductor MDS-JE330 Main SW VOL SEL Vibrator
Top Page Image Contents