Sony 4-216-349-5, Singapore model Section Disassembly, Case and Front Panel, Slider CAM

Page 12

SECTION 3

DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

3-1. CASE AND FRONT PANEL

3 Case

2 Two screws (Case)

1 Two screws (Case)

4 Flat type wire (CN421)

6 Front panel assembly

5Five screws (BVTP3x8)

3-2. SLIDER (CAM)

6Slider (Cam)

• Note for Installation of Slider (Cam)

Set the shaft of Cam gear to be at the position in the figure.

2 Bracket (Guide L)

1 Two screws (BTP2.6x6)

Set the shaft of Lever (O/C) to

3 Leaf spring	be at the position in the figure.
	be at the position in the figure.
	4 Two screws (BTP2.6x6)

5Bracket (Guide R)

– 12 –

Image 12

Contents Specifications MDS-JE330SELF-DIAGNOSIS Function Items of Error History Mode Items and Contents Flexible Circuit Board Repairing VarnigTable of Contents DisassemblyDiagrams Exploded ViewsSection Servicing Note JIG for Checking BD Board WaveformIOP TEORecord Precedure Checks Prior to Parts Replacement and Adjustments Forced ResetCriteria for Determination Measure if unsatisfactory REC/PLAY Retry Cause Display Mode Bit BinaryBit When Binary Higher Bits Lower Bits Hexa DetailsHexadecimal Binary Section General Location of Parts and ControlsFront Panel Section Disassembly Case and Front PanelSlider CAM Base Unit MBU-5A and BD Board SW Board and Loading Motor M103Section Test Mode Precautions for USE of Test ModeSetting the Test Mode Exiting the Test ModeSelecting the Test Mode GroupOperating the Continuous Playback Mode Non-Volatile Memory Mode EEP ModeMID OUTTest Mode Displays Functions of Other ButtonsMeanings of Other Displays Section Electrical Adjustments Parts Replacement and AdjustmentPrecautions for Checking Laser Diode Emissinon Precautions for USE of Optical PICK- UP KMS-260APrecautions for Adjustments Creating Continuously Recorded DiscTemperature Compensation Offset Check Laser Power CheckChecks Prior to Repairs Specified ValuePlay Checking MO Error Rate Check CD Error Rate CheckFocus Bias Check Self-Recording/playback CheckInitial Setting of Adjustment Value Temperature Compensation Offset AdjutmentLaser Power Adjustment Recording and Displaying the IOP InformationTraverse Adjustment Focus Bias Adjustment Error Rate Check Auto Gain Control Output Level AdjustmentCD Auto Gain Control Output Level Adjustment MO Auto Gain Control Output Level AdjustmentAdjusting Points and Connecting Points Section Diagrams Circuit Boards LocationBlock Diagrams BD Section MDS-JE330Main Section LD-LOVOFor schematic diagrams For printed wiring boardsWaveforms Display SectionPrinted Wiring Board BD Section Semiconductor LocationSchematic Diagram BD 1/2 Section Schematic Diagram BD 2/2 Section Schematic Diagram Main 1/2 Section Schematic Diagram Main 2/2 Section Printed Wiring Board Main Section Printed Wiring Board Panel Section Schematic Diagram Panel Section Schematic Diagram BD Switch Section IC Block Diagrams Printed Wiring Board BD Switch SectionBD Section IC101 IC121 CXD2654R IC152 BH6511FS-E2Main section IC301 UDA1341TS/N2 IC381 M5218AL IC441 LB1641IC406 M62016L IC PIN Functions IC101 RF Amplifier CXA2523AR BD boardPin No Pin Name Function MNT0 FOK MNT1 ShckMNT2 Xbusy MNT3 SlocMvci AsyoAsyi AvddTfdr FfdrFrdr FS4IC501 System Control M30620MC-400FP Main board OPT DEL OPT SEL Mode SEL PB-PREC/PB SDASection Exploded Views Case and Back Panel SectionFront Panel Section 6162Mechanism Section MDM-5A 225 226 206 205Base Unit Section MBU-5A 251 252Section Electrical Parts List ResistorsDisplay Display KEY SW Main PIN, Connector 7P Inductor MDS-JE330 Main SW VOL SEL Vibrator