RCA 19V400TV manual Damage Requiring Service, Replacement Parts, Safety Check, Heat, NEC Section

Page 4

IMPORTANT SAFEGUARDS

19.DAMAGE REQUIRING SERVICE

Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the unit.

c.If the unit has been exposed to rain or water.

d.If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operat- ing instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.

e.If the unit has been dropped or the cabinet has been damaged.

f . When the unit exhibits a distinct change in performance, this indicates a need for service.

20.REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

21.SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

22.HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

23.NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

 

ANTENNA LEAD IN WIRE

GROUND CLAMP

 

 

ANTENNA DISCHARGE UNIT

 

(NEC SECTION 810-20)

ELECTRIC SERVICE

GROUNDING CONDUCTORS

EQUIPMENT

(NEC SECTION 810-21)

 

GROUND CLAMPS

NEC-NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

S2898A

ELECTRODE SYSTEM

 

(NEC ART 250, PART H)

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents TV/VCR Cleaning Read InstructionsRetain Instructions Heed WarningsAccessories Power SourcesPOWER-CORD Protection Power LinesDamage Requiring Service Replacement PartsSafety Check HeatPrecautions Table of ContentsFeatures Front Rear Location of ControlsDescription of Controls Remote Control Reset Button Used to reset the counter to1019 1523Power Source Battery InstallationBattery Precautions Effective Distance of the RE Mote ControlOhm Coaxial Cable Ohm Matching Transformer Antenna ConnectionsCombiner UHF 300 ohm VHF 300 ohm Setting the Language For Subscribers with Basic Cable TV ServiceFor Subscribers with Scrambled Cable TV Service Cable TV ConnectionsAuto Clock Setting Manual Clock Setting TV OperationVHF/UHF/CATV Channels To Select Catv ChannelsMuting Channel +Call SleepTo Memorize Channels Automatic Memory TuningTV/CATV Selection Setting the V-CHIP To ADD/DELETE ChannelsTo SET the V-CHIP To Change PasswordTo use the TV after the TV is protected To SET the on Timer To SET the OFF TimerPicture Control Adjustments Sound Control AdjustmentsPlayback Special Playback ONE-TOUCH Timer Recording OTR Timer RecordingUsing the Real Time Tape Counter Stereo Recording and Playback Second Audio Program SAPRecording Stereo Broadcasts Output SelectionConnection to Another VCR Duplicating a Video TapeConnection to Camcorder Troubleshooting Guide Symptom Cause Possible Solution PowerNo power TV Broadcast ReceptionSymptom Cause Possible Solution Remote ControlRecording PlaybackVideo Head Cleaning Reception DisturbancesSpecifications TelevisionLimited Warranty If you purchased your product outside the United States 03/12 K
Top Page Image Contents