SUPER MICRO Computer 6014L-M manual Floppy Connector, Sata Connectors

Page 59

Chapter 5: Advanced Serverboard Setup

Floppy Connector

Floppy Drive Connector

Pin Deﬁnitions (Floppy)

The ﬂ oppy connector is des- ignated "Floppy". See the table to the right for pin deﬁ nitions.

Pin# Deﬁ nition

1Ground

3Ground

5Key

7Ground

9Ground

11 Ground

13Ground

15Ground

17Ground

19Ground

21Ground

23Ground

25Ground

27Ground

29Ground

31 Ground

33 Ground

Pin # Deﬁ nition

2FDHDIN

4Reserved

6FDEDIN

8Index

10Motor Enable

12Drive Select B

14Drive Select B

16Motor Enable

18DIR

20STEP

22Write Data

24Write Gate

26Track 00

28Write Protect

30Read Data

32 Side 1 Select

34 Diskette

SATA Connectors

There are no jumpers to con-

ﬁgure the onboard SATA con- nectors. See the table on the right for pin deﬁ nitions.

SATA Connector Pin Deﬁnitions

(I-SATA0, I-SATA1)

Pin #

Deﬁ nition

1Ground

2TXP

3TXN

4Ground

5RXN

6RXP

7Ground

5-23

Image 59

Contents Super Manual Revision Release Date February 23 Manual Organization PrefaceAbout This Manual Bios System SafetyAdvanced Serverboard Setup Advanced Chassis SetupPreface Table of Contents Advanced Serverboard Setup System SafetyAdvanced Chassis Setup Appendices BiosPage Overview Chapter IntroductionPCI Expansion Slots Serverboard FeaturesProcessors Memory Serial ATAOnboard Controllers/Ports Other FeaturesIntel E7520 Chipset System Block Diagram Server Chassis Features Asia-Paciﬁc Contacting SupermicroHeadquarters EuropeUnpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Rack hardware optional Installing the System into a RackBasic Installation Procedure Installing the Chassis Rails Installing with Rackmount KitInstalling the Server into the Rack Installing the Rack RailsInstalling the Server into a Rack Optional Rackmount Kit Installing the Server into a Telco RackAccessing the inside of the server Figure Checking the Serverboard SetupCheck the system memory Check all cable connections and airﬂow Installing add-on cardsChecking the Drive Bay Setup Page Control Panel Buttons Chapter System InterfaceControl Panel LEDs Page Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsUnpacking Chapter Advanced Serverboard SetupPrecautions Handling the ServerboardInstalling the Serverboard Serverboard InstallationInstalling the Heatsink Brackets Installing the Processors Processor and Heatsink InstallationInstalled heatsink Installing the HeatsinksInstalled processor Removing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables I/O Ports Connecting the Control PanelMemory Support Installing MemoryDimm Installation See Figure PCI slots PCI card installationAdding PCI Cards Super X6DLP-EG2 Layout Serverboard DetailsX6DLP-EG2 Quick Reference Jumper Description Default SettingConnector Description Onboard Indicators DescriptionPower LED Connector DeﬁnitionsATX Power Connector Processor Power ConnectorOverheat/Fan Fail LED Power Fail LEDNIC1/2 LEDs Chassis Intrusion Reset ButtonPower Button JLAN1/2 Ethernet PortsFan Headers Universal Serial Bus USB0/1Universal Serial Bus Headers Wake-On-LAN Speaker/Power LED/KeylockWake-On-Ring ATX PS/2 Keyboard and PS/2 Mouse Ports ConnectorPower Fault SMB Power I2 CCmos Clear Jumper SettingsJLAN1/2 Enable/Disable Explanation JumpersWatch Dog VGA Enable/DisablePower Force On SMBus to PCI SlotsSystem Status LED Onboard IndicatorsAlarm Reset Jlan LEDsOnboard LED Indicators DS7, DS8 Onboard LED Indicators DS1, DS5Parallel Printer Port Header Parallel Port, Floppy, IDE and Sata Drive ConnectionsSata Connectors Floppy ConnectorIDE Drive Connectors Pin Deﬁnitions IDE1, IDE2 IDE ConnectorsTools Required Chapter Advanced Chassis SetupPrecautions Static-Sensitive DevicesSystem Fans Control PanelRemoving a fan Installing a new fanSystem Fan Failure Replacing System Cooling FansSerial ATA Drive Installation Drive Bay Installation/RemovalAccessing the Drive Bays CD-ROM Drive Installation Power Supply Failure Power SupplyInstalling a new power supply Replacing the Power SupplyAccessing the inside of the system Removing the power supplyPage Introduction How To Change the Conﬁguration DataChapter System Memory Main SetupProcessors System Time/System Date Advanced SettingsConﬁgure Advanced CPU Settings CPU Conﬁguration Sub-MenuATA Ports Deﬁnition Combined Mode OperationIDE Conﬁguration Sub-Menu IDE ConﬁgurationA.R.T. For Hard disk drives LBA/Large ModeType Block Multi-Sector TransferPCI/PnP Conﬁguration Floppy ConﬁgurationOffboard PCI/ISA IDE Card Allocate IRQ to PCI VGAPalette Snooping PCI IDE BusMasterSuper IO Conﬁguration Sub-Menu Advanced Chipset Settings Apci Conﬁguration Power ConﬁgurationEvent Log Conﬁguration Watch Dog TimerPCI/PCI Error Logging PCI/PCI Express Error LoggingPCI Express Conﬁguration Remote Access ConﬁgurationMPS Conﬁguration Sredir Memory Display Delay Remote AccessSerial Port Mode Redirection After Bios PostSystem Health Monitor USB ConﬁgurationFan1 Speed to Fan6 Speeds Boot SettingsSystem Fan Monitor Fan Speed Control ModesBios Settings Conﬁguration CD/DVD Drives Boot Device PriorityHard Disk Drives Removable DrivesClear User Password Security SettingsChange Supervisor Password Change User PasswordDiscarding Changes and Exit Load Optimal DefaultsExit Options Saving Changes and ExitLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesAmibios Error Beep Codes DS7/DS8 LED Post Codes LED IndicatorsUncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Intel 6300ESB I/O Controller Hub Appendix C Software InstallationSerial ATA Sata Adaptec RAID Conﬁguration Utility ARC Conﬁguring Sata RAIDAdaptec Sata HostRAID Controller Driver Using the Array Conﬁguration Utility ACU Viewing Array Properties Managing ArraysCreating Arrays Deleting ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array To initialize drives Deleting a Bootable ArrayInitializing Disk Drives Page Page To rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesYou can choose from the following options Exiting the Adaptec RAID Conﬁguration UtilityInstalling the ICH5R/6300 ESBDriver Installing Additional Drivers Installing Other Software Programs and DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Speciﬁcations System Input Requirements WeightPower Supply System Cooling