SUPER MICRO Computer 6014L-M manual IDE Connectors, IDE Drive Connectors Pin Deﬁnitions IDE1, IDE2

Page 60

SUPERSERVER 6014L-M User's Manual

IDE Connectors

There are no jumpers to con- ﬁgure the onboard IDE connec- tors. See the table below for pin deﬁ nitions.

IDE Drive Connectors

Pin Deﬁnitions (IDE1, IDE2)

Pin# Deﬁ nition

1Reset IDE

3 Host Data 7

5 Host Data 6

7 Host Data 5

9 Host Data 4

11 Host Data 3

13 Host Data 2

15 Host Data 1

17 Host Data 0

19 Ground

21 DRQ3

23I/O Write

25I/O Read

27IOCHRDY

29DACK3

31IRQ14

33Addr1

35Addr0

37Chip Select 0

39Activity

Pin # Deﬁ nition

2Ground

4Host Data 8

6 Host Data 9

8 Host Data 10

10 Host Data 11

12 Host Data 12

14 Host Data 13

16 Host Data 14

18 Host Data 15

20 Key

22 Ground

24Ground

26Ground

28BALE

30Ground

32IOCS16

34Ground

36Addr2

38Chip Select 1

40Ground

5-24

Image 60

Contents Super Manual Revision Release Date February 23 Preface About This ManualManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup Bios AppendicesPage Chapter Introduction OverviewServerboard Features Processors MemorySerial ATA PCI Expansion SlotsOther Features Onboard Controllers/PortsIntel E7520 Chipset System Block Diagram Server Chassis Features Contacting Supermicro HeadquartersEurope Asia-PaciﬁcChapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Installing the System into a Rack Basic Installation ProcedureRack hardware optional Installing with Rackmount Kit Installing the Chassis RailsInstalling the Rack Rails Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Rack Optional Rackmount KitChecking the Serverboard Setup Accessing the inside of the server FigureCheck the system memory Installing add-on cards Check all cable connections and airﬂowChecking the Drive Bay Setup Page Chapter System Interface Control Panel ButtonsControl Panel LEDs Page Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard UnpackingServerboard Installation Installing the Heatsink BracketsInstalling the Serverboard Processor and Heatsink Installation Installing the ProcessorsInstalling the Heatsinks Installed processorInstalled heatsink Removing the Heatsink Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel I/O PortsInstalling Memory Dimm Installation See FigureMemory Support PCI card installation Adding PCI CardsPCI slots Serverboard Details Super X6DLP-EG2 LayoutJumper Description Default Setting Connector DescriptionOnboard Indicators Description X6DLP-EG2 Quick ReferenceConnector Deﬁnitions ATX Power ConnectorProcessor Power Connector Power LEDPower Fail LED NIC1/2 LEDsOverheat/Fan Fail LED Reset Button Power ButtonJLAN1/2 Ethernet Ports Chassis IntrusionUniversal Serial Bus USB0/1 Universal Serial Bus HeadersFan Headers Speaker/Power LED/Keylock Wake-On-RingWake-On-LAN Connector Power FaultSMB Power I2 C ATX PS/2 Keyboard and PS/2 Mouse PortsJumper Settings JLAN1/2 Enable/DisableExplanation Jumpers Cmos ClearVGA Enable/Disable Power Force OnSMBus to PCI Slots Watch DogOnboard Indicators Alarm ResetJlan LEDs System Status LEDOnboard LED Indicators DS1, DS5 Onboard LED Indicators DS7, DS8Parallel Port, Floppy, IDE and Sata Drive Connections Parallel Printer Port HeaderFloppy Connector Sata ConnectorsIDE Connectors IDE Drive Connectors Pin Deﬁnitions IDE1, IDE2Chapter Advanced Chassis Setup PrecautionsStatic-Sensitive Devices Tools RequiredControl Panel System FansInstalling a new fan System Fan FailureReplacing System Cooling Fans Removing a fanDrive Bay Installation/Removal Accessing the Drive BaysSerial ATA Drive Installation CD-ROM Drive Installation Power Supply Power Supply FailureReplacing the Power Supply Accessing the inside of the systemRemoving the power supply Installing a new power supplyPage How To Change the Conﬁguration Data ChapterIntroduction Main Setup ProcessorsSystem Memory Advanced Settings Conﬁgure Advanced CPU SettingsCPU Conﬁguration Sub-Menu System Time/System DateCombined Mode Operation IDE Conﬁguration Sub-MenuIDE Conﬁguration ATA Ports DeﬁnitionLBA/Large Mode TypeBlock Multi-Sector Transfer A.R.T. For Hard disk drivesFloppy Conﬁguration PCI/PnP ConﬁgurationAllocate IRQ to PCI VGA Palette SnoopingPCI IDE BusMaster Offboard PCI/ISA IDE CardSuper IO Conﬁguration Sub-Menu Advanced Chipset Settings Power Conﬁguration Apci ConﬁgurationWatch Dog Timer PCI/PCI Error LoggingPCI/PCI Express Error Logging Event Log ConﬁgurationRemote Access Conﬁguration MPS ConﬁgurationPCI Express Conﬁguration Remote Access Serial Port ModeRedirection After Bios Post Sredir Memory Display DelayUSB Conﬁguration System Health MonitorBoot Settings System Fan MonitorFan Speed Control Modes Fan1 Speed to Fan6 SpeedsBios Settings Conﬁguration Boot Device Priority Hard Disk DrivesRemovable Drives CD/DVD DrivesSecurity Settings Change Supervisor PasswordChange User Password Clear User PasswordLoad Optimal Defaults Exit OptionsSaving Changes and Exit Discarding Changes and ExitLoad Fail-Safe Defaults Appendix a Bios Error Beep Codes Amibios Error Beep CodesBeep Code Error Message Description LED Indicators DS7/DS8 LED Post CodesAppendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C Software Installation Serial ATA SataIntel 6300ESB I/O Controller Hub Conﬁguring Sata RAID Adaptec Sata HostRAID Controller DriverAdaptec RAID Conﬁguration Utility ARC Using the Array Conﬁguration Utility ACU Managing Arrays Viewing Array PropertiesDeleting Arrays Creating ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array Deleting a Bootable Array Initializing Disk DrivesTo initialize drives Page Page Rebuilding Arrays To rebuild an arrayUsing the Disk Utilities To access the disk utilitiesExiting the Adaptec RAID Conﬁguration Utility You can choose from the following optionsInstalling the ICH5R/6300 ESBDriver Installing Other Software Programs and Drivers Installing Additional DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Speciﬁcations Weight Power SupplySystem Cooling System Input Requirements