Toshiba RD-XV47KE manual EN105, Symptom Solution

E3B90ED_EN.book Page 105 Friday, February 23, 2007 12:38 PM

T

	Symptom		Solution
	The power does not turn on.	• Check that the AC power cord is connected securely.
		• Batteries of the remote control are weak.
	The unit turns on automatically without any	• The unit turns on automatically 2 minutes before the Timer Recording.
	operation.
POWER
	The OSD Language Menu appears every	• Finish up the Language Setting procedure by selecting a language in the
	time the power turns on.	OSD Language Menu. Press [ENTER] to activate the setting.
	The power turns off automatically.	• The power turns off automatically when abnormality is detected on the
		disc. Press [	ON / STANDBY] or [OPEN / CLOSE O] on the unit to
		open the disc tray, and before it is opened completely, press the button
		again. Then take out the disc.
		• The power turns off automatically when an OTR is completed.

	Symptom	Solution
	The unit does not function.	• “ ” or error message appears if the operation is prohibited.
		• Batteries of the remote control are weak or exhausted.
	No picture, sound or menu appears on the	• Check if the connections are made securely and correctly.
GENERAL	screen.	• Check if the cables are damaged.
	Clock Setting and Channel Setting cannot be	• Check if a correct external input channel is selected on your TV. (See
		page 25.)
		• Check if you have completed the Channel Setting. (See pages 27 to 30.)
	performed.	• If a recording is in progress, these operations cannot be performed.
	The unit does not operate properly.	• Moisture has condensed inside the unit. Remove the disc and leave the
		unit turned on for about two hours until the moisture evaporates. (See
		page 3.)

	Symptom	Solution
	TV channels cannot be changed.	• Check if the connections are made securely and correctly.
CHANNEL	The external input channels (such as AV1,	• Check if the cables are damaged.
		• This unit does not skip the external input channels. This is not a
		• Try Channel Setting by following the steps on pages 27 to 30.
	Only specific channels do not appear.	• The channels may be set to be skipped. (See page 28.)
	AV2 or AV3) cannot be skipped.	malfunction.

Introduction Connections Basic Setup Recording Playback

		Symptom	Solution
	GENERAL	The image from the external device
		cannot be displayed or recorded.	• Try pressing [INPUT SELECT	] repeatedly.
			• Turn on all connected devices.
			• Check if the connections are made securely and correctly.
		Recording is impossible.	• This unit cannot record programmes that contain copy protection signal.
			This is not a malfunction.
			• The space of the recording media may be used up. Try deleting
	HDD/DVD		unnecessary titles from the Original, or exchange it with the recordable
RECORDING			media.
			• The maximum number of titles or chapters has exceeded.
			Delete the unnecessary titles to make enough space or insert a new
			recordable media.
			• Check if the connections are made securely and correctly.
		Timer Recording cannot be performed.	• The internal clock of the unit may have been stopped due to a power
			failure that lasted for more than 30 seconds. Reset the clock. (See pages
			30 to 31.)
		Recording is impossible.	• Copy-once programmes can only be recorded on a CPRM compatible
			VR mode DVD-RW.
			• Check if the disc is protected or finalised. Undo the protection or the
	DVD		finalisation.
			• DVD-RW once formatted with other DVD recorders cannot be recorded
			on this unit. This is not a malfunction.
			• Video mode DVDs recorded by other DVD recorders cannot be used on
			this unit unless finalised.
			• Check if the connections are made securely and correctly.
	VCR	Recording is impossible.	• Check if a videotape is inserted.
			• Check if a videotape has a record tab intact.

EN105

Editing Function Setup VCR Functions Others