Toshiba RD-XV47KE manual 44 EN, Press Timer PROG. to exit

E3B90ED_EN.book Page 44 Friday, February 23, 2007 12:38 PM

3Recording Date:

When press [Cursor D] at the current date, the setting will change as follows.

e.g., 1st January

• If you press [	ON / STANDBY] to turn the
unit to standby mode, it will turn on 2 minutes
before the programmed recording time, and
start recording at the programmed recording
time. When the recording is completed, the unit

01/01

Daily

M-F

W-Sat

W-Fri

W-Sun

31/01

Weekly recording

will ask you whether to turn off the unit.

The unit will be turned off automatically if you

select “Yes” or if you do not reply in 1 minute.

• To stop recording in progress, press [STOP S].

Confirmation message will appear. Select “Yes”

using [Cursor L / P].

Relay Recording:

When you Timer Record to DVD, the unit automatically changes the recording media to HDD under the conditions listed below:

- when there is no recordable disc in the unit.

Skip:

Select this item only when you want to deactivate the periodical (Daily, Mon-Fri or Weekly) Timer Recording temporarily. To do so, move the cursor to the Skip section and then press

[Cursor U / D].

Check mark will appear and press [ENTER] to activate the setting.

4Start Time:

5End Time:

6Rec Mode:

Refer to “Rec Mode” on page 35.

7Recording Media (HDD or DVD):

To record onto the HDD, select “HDD”. To record onto a disc, select “DVD”. VCR is not compatible with Timer Recording.

8VPS/PDC system:

Refer to “VPS (Video Programme System) / PDC (Programme Delivery Control)” on page 45.

•VPS/PDC system is only available for HDD.

•VPS/PDC system is not available for periodical timer programme.

3 Select an item to set using [Cursor L / P], and set the contents to suit your preference using [Cursor U / D].

4 Press [ENTER] when all the information is entered.

The icon will appear on the Front Panel Display indicating one or more Timer Recordings are in standby.

•Press [CLEAR] will reset all the entered information.

•To set another programme, repeat steps 2 to 4.

•When programmes are overlapped, a warning

message “All or part of the programme will not be recorded.” will appear.

-When icon appears, a part of the programme will not be recorded.

-When icon appears, the whole programme will be recorded.

For details on overlapped Timer Programmings, refer to “Hints for Timer Recording” on page 45.

5 Press [TIMER PROG.] to exit.

• You can also press [SETUP] twice to exit.

- when the disc does not have enough space for

the recording.

- if the unit is formatting or finalising a disc.

This feature is available only for Timer Recording but not for OTR.

Note

•If you have not set the clock, the clock setting window will appear instead of Timer Programme List at step 1. Continue from step 3 in “Setting the Clock” on page 30 before programming the timer.

•If a basic recording or One-touch Timer Recording is in progress on the VCR and the Timer Recording set for HDD or DVD is about to begin, the unit will automatically switch to the programmed channel within 15 seconds before the programmed time, and the recording in progress on the VCR will be cancelled UNLESS their recording channel is the same. If their recording channel is the same, the Timer Recording for HDD or DVD will start without cancelling the recording currently in progress on the VCR. In this case, the recording of the same channel will be made on both VCR and the HDD or DVD.

•The maximum recordable duration is 7 hours for Video mode discs, 8.5 hours for VR mode discs and

5hours for +VR mode discs.

•If the recording time exceeds 12 hours, a Timer Recording cannot be set.

•If the starting time you entered is already in the past, the recording will start as soon as you activate the Timer Recording by pressing [ENTER] at step 4.

•If playback and recording are in progress at the same time, select the appropriate device by pressing [HDD], [DVD] or [VCR] before you press [PAUSE p] or [STOP S] to pause or stop the operation.

•When the Timer Recording is finished, confirmation message will appear. If there is no signal for about

1minute, unit will turn off automatically.

•If DVD+RW / R were used for the Timer Programming with SLP mode, the Rec Mode will change to EP mode.

•When VPS / PDC is set to “On” for timer recording, you may hear some noise from the unit while the unit is in timer standby mode. This is not a malfunction.

44 EN