Toshiba kV-9168A Alarm Recording, Operation at Alarm Input, Event Recording, Alarm Recall Display

Page 30

PREPARATIONINTRODUCTION

ALARM RECORDING

If an alarm condition arises, the alarm function operates with an alarm input signal.

Operation at Alarm Input

When there is an alarm during recording, recording pause or stop modes, the VCR automatically goes into alarm recording mode. The VCR can be programmed to record in the following time modes during alarm recording: SPA2, EPA6, SPA12, EPA18, SPA24.

Alarm input

 

 

 

 

Recording

SPA2, EPA6,

SPA12,

Recording

Recording pause

Recording pause

EPA18, SPA24 mode

Stop

Stop

 

 

 

 

 

 

Alarm Recording

iWhen there is an alarm input in the STOP mode, a slight delay will occur in start of the alarm recording.

iWhen the pause mode continues for 10 minutes the VCR goes to the stop mode. This occurs in order to protect the video heads and tape. While in pause mode, the video head is constantly tracing the same location.

iAlarm recording will not operate from power off mode and timer standby mode.

RECORDING

OPERATION

 

 

PLAYBACK

OPERATION

 

 

Event Recording

If event recording is desired, set the VCR’s recording mode to SPL01, SPL02 or SPL03. In order to accomplish this press the time mode button until “SPL01”, “SPL02” or “SPL03” is shown.

If there is no alarm input present when in “SPL01”, “SPL02” or “SPL03” mode, the VCR automatically forwards 2 fields with recording every appointed time (SPL01: 1min, SPL02: 2min, SPL03: 3min.) to protect the tape and the video head from damage.

Warning at Alarm Recording

When an alarm signal is input, the buzzer sounds and the alarm display on the VCR DISPLAY lights.

Alarm display lights and then blinks when alarm recording is finished.

 

ALARM

H

 

 

 

 

 

 

REC

SP

 

 

 

 

 

 

 

 

 

 

 

The day of the week display

 

 

 

 

changes to the alarm number

 

Changes to a display of SPA2, EPA6, SPA12,

8/28/97 A01

during alarm recording.

 

 

 

EPA18 or SPA24.

 

17:30:13SPA 2 Changes to a display of SPA2,

 

 

 

• Turn off the BUZZER switch to stop the buzzer.

 

 

EPA6, SPA12, EPA18 or SPA24.

•To stop the alarm display blinking, press the ALARM button to change the counter display to the alarm counter and then press the RESET button.

Alarm Recall Display

Check the alarm input information on the ALARM RECALL screen.

NOTICE

M E N U

CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH

END=[DISPLAY]

 

 

 

 

 

 

ALARM RECALL

 

 

AL1

8/19/97TUE 20:35:09

 

AL2

8/ 7/97THU 21:35:16

 

AL3

7/25/97FRI 0:14:12

 

AL4

7/12/97SAT 19:14:12

 

AL5

6/20/97FRI 23:14:10

 

AL6

4/ 1/97TUE 21:07:13

 

AL7 --/--/----- --:--:--

 

1ST

4/ 1/97TUE 21:07:13

 

 

MENU=[DISPLAY]

 

 

 

 

•At 1ST, the first (oldest) alarm input information is displayed.

•At AL1, the latest alarm input information is displayed.

•When more than seven items are input, the old information is erased and the new information is stored in the memory.

•To erase the alarm recall contents, press the ALARM button to change the counter display to alarm counter and press the

29 RESET button.

Page 29 Page 31
Image 30
Page 29 Page 31
Contents
Instruction Manual Important Precautions Please ReadRadiators, heat registers, stoves Important Safety InstructionsPower Sources Unplug this product from the wallWhen the power-supply cord or plug is damaged AccessoriesPower Lines To restore the product to its normal operationFeatures Table of ContentsInstructions in Brief Front PanelCassette Compartment Time Mode / SET + buttonsTape Remain button Display buttonRear Panel Installation Word on the Exclusive 3N-100AAS Battery PackSpecification of Battery RemovalVCR Display REW button Press to start play backFF button Connections Connection with a Video CameraTo REC TRIGG. OUT Typical Connection with the Sequential SwitcherVideo OutputContents of Screen Display Alarm Recall Screen Setting the Clock OperationVCR display ON-SCREEN FunctionsDate-Time Display Monitor screenDisplay Screen Changes to the alarm number Alarm numberIs pressed. When an alarm is This function enables to indicate and record informationAlarm Memory Counter DisplaysCounter Memory Error Message Tape RemainCode Number Condition of Abnormality Setting the RECORDING/PLAYBACK Time HOW to Operate 24 Hour Virtual Real Time ModeA18 20s Fields/s Possible Continuous Virtual Real Time mode Loading and Unloading a Video Cassette Loading a cassetteUnloading a Cassette Recording Camera and monitor TVSetting the Restart Recording Restart Recording Daily Timer Recording Timer Recording Setting the Timer Program Program ScreenShould be more than 1 minute. If they are same, timer Time Mode button is pressed, the displayPower goes off and the Timer display lights During timer power off mode, alarm recording will notWeekly Timer Recording Press the Shift ButtonGRAM.to blink PROPress the Shift Button to blink the MO1 start time FR2 Overlapping ProgramsExample DLYAlarm Recall Display Alarm RecordingOperation at Alarm Input Event RecordingConnecting the Alarm Terminals Cont Setting the Alarm RecordingDisplay Recording time ManualOperation of Auto Recording Connecting the External control terminalAuto Recording Auto recordingPress Timer button to release the timer mode How to release Auto RecordingHow to forbid Auto Recording Press the + or SETOperation After Tape END Detection How to Set to Stop at End of TapeSetting contents Buzzer Screen display Counter display Display Operation after detection of tape endHow to Set to Auto Rewind at End of Tape Alarm recording does not operate during auto-rewindMenu Screen How to Set to Repeat Record at End of Tape ButtonREC. to select REW →Timing for Camera Switching Recording with the Sequential SwitcherConnection with the Sequential Switcher C D a B C DREC Trigger Output Selection in the Alarm Recording Tracking Adjustment Recording time mode Time mode for playbackPlayback Picture Search Play Using the Shuttle DialREW Stop Slow Still PlayPlayback in Various Modes Time Date Search Search OperationStill picture mode Press the Play button Alarm SearchAlarm M to light Press the Counter Memory button twice to makeSignal Levels of INPUT/OUTPUT Terminals Input/Output Terminal Signal level Additional remarksDaily and Periodic Inspection Check the playback picture recorded in SPA2 modePress the or Time Mode button to go to SPA2 mode Order of Daily ChecksRequest for Periodic Checks Recording Usage frequency Time modeSteps to Take after Daily Checks Tape Usage FrequencyDew Condensation Function/Operation Before Calling Service PersonnelInstallation RecordingPlayback Other mattersAccessories SpecificationsConnector section Dew caution sheetLimited Warranty 70971825
Top Page Image Contents