Toshiba kV-9168A Specifications, Connector section, Accessories, Dew caution sheet

Page 51

SPECIFICATIONS

Power supply	120V AC, 60 Hz

Power consumption	18W
External dimensions	17 × 3-5/8 × 12-1/2 inch (W × H × D), 430 × 92 × 318 mm (W × H × D)

Weight	11 lbs (5.0 kg)

Signal system	Standard NTSC color television system

Recording System	Rotary 2-head azimuth

Cassette	VHS marked, 1/2 inch cassette tape
Tape speed	SPA2 mode: 33.35mm/s, EPA6 mode: 11.12mm/s
Recording/playback time mode	SP modes: A2, A12, A24, 24, 48, 72, 120, 168
	EP modes: A6, A18, 30, 48, 72, 120, 168
Fast forward/rewind time	Within 2 minutes (when T-120 is used)
Video input (BNC)	1.0V(p-p), 75 Ω Unbalanced Luminance signal

Video output (BNC)	1.0V(p-p), 75 Ω Unbalanced Luminance signal

Horizontal resolution	350 lines (monochrome mode), 300 lines (color mode) (SPA2 mode)
Video S/N	More than 45 dB: monochrome mode (SPA2 mode)
	More than 45 dB: color mode (SPA2 mode)

Audio input	Line input: 308mV (rms), more than 47k Ω, pin jack
	Microphone input: 0.245mV (rms), less than 5k Ω, ø3.5 jack

Audio output	388mV (rms), less than 4.7k Ω, pin jack

No. of audio tracks	1 track
Audio frequency characteristics	100 Hz to 10 kHz (SPA2 mode)
Audio S/N	More than 43 dB (SPA2 mode)

Operating conditions	Temperature: 41°F to 104°F (5°C to 40°C)
	Humidity: less than 80%
Storage conditions	–4°F to 140°F (–20°C to 60°C)
Connector section
Alarm input	Ground input: 0 to 0.5V
Alarm reset input	Ground input: 0 to 0.5V

Alarm output	DC 5V, impedance: 230 Ω, less than 10mA
Recording trigger output	During time lapse: 0/5V negative pulse signal
	SPA2 and EPA6 mode: 0V
	Alarm recording: 0/5V (Programmable)
	Except above-mentioned: 5V

Tape end output	Open/Short, impedance: 220 Ω, less than 20mA

External control input	Ground input: 0 to 0.5V

Design and specifications are subject to change without notice.

Accessories
• Instruction manual	(1)
• Dew caution sheet	(1)

INTRODUCTION

PREPARATION

RECORDING

OPERATION

PLAYBACK

OPERATION

NOTICE

50

Image 51

Contents Instruction Manual Please Read Important PrecautionsUnplug this product from the wall Important Safety InstructionsPower Sources Radiators, heat registers, stovesTo restore the product to its normal operation AccessoriesPower Lines When the power-supply cord or plug is damagedTable of Contents FeaturesFront Panel Instructions in BriefDisplay button Time Mode / SET + buttonsTape Remain button Cassette CompartmentRear Panel Removal Word on the Exclusive 3N-100AAS Battery PackSpecification of Battery InstallationVCR Display REW button Press to start play backFF button Connection with a Video Camera ConnectionsOutput Typical Connection with the Sequential SwitcherVideo To REC TRIGG. OUTContents of Screen Display Alarm Recall Screen Operation Setting the ClockMonitor screen ON-SCREEN FunctionsDate-Time Display VCR displayDisplay Screen This function enables to indicate and record information Alarm numberIs pressed. When an alarm is Changes to the alarm numberAlarm Memory Counter DisplaysCounter Memory Error Message Tape RemainCode Number Condition of Abnormality Setting the RECORDING/PLAYBACK Time HOW to Operate 24 Hour Virtual Real Time ModeA18 20s Fields/s Possible Continuous Virtual Real Time mode Loading and Unloading a Video Cassette Loading a cassetteUnloading a Cassette Camera and monitor TV RecordingRestart Recording Setting the Restart RecordingProgram Screen Timer RecordingSetting the Timer Program Daily Timer RecordingDuring timer power off mode, alarm recording will not Time Mode button is pressed, the displayPower goes off and the Timer display lights Should be more than 1 minute. If they are same, timerWeekly Timer Recording Press the Shift ButtonGRAM.to blink PROPress the Shift Button to blink the MO1 start time DLY Overlapping ProgramsExample FR2Event Recording Alarm RecordingOperation at Alarm Input Alarm Recall DisplayConnecting the Alarm Terminals Manual Setting the Alarm RecordingDisplay Recording time ContAuto recording Connecting the External control terminalAuto Recording Operation of Auto RecordingPress the + or SET How to release Auto RecordingHow to forbid Auto Recording Press Timer button to release the timer modeDisplay Operation after detection of tape end How to Set to Stop at End of TapeSetting contents Buzzer Screen display Counter display Operation After Tape END DetectionHow to Set to Auto Rewind at End of Tape Alarm recording does not operate during auto-rewindMenu Screen ButtonREC. to select REW → How to Set to Repeat Record at End of TapeC D a B C D Recording with the Sequential SwitcherConnection with the Sequential Switcher Timing for Camera SwitchingREC Trigger Output Selection in the Alarm Recording Tracking Adjustment Recording time mode Time mode for playbackPlayback Slow Still Play Using the Shuttle DialREW Stop Picture Search PlayPlayback in Various Modes Search Operation Time Date SearchPress the Counter Memory button twice to make Alarm SearchAlarm M to light Still picture mode Press the Play buttonInput/Output Terminal Signal level Additional remarks Signal Levels of INPUT/OUTPUT TerminalsOrder of Daily Checks Check the playback picture recorded in SPA2 modePress the or Time Mode button to go to SPA2 mode Daily and Periodic InspectionTape Usage Frequency Recording Usage frequency Time modeSteps to Take after Daily Checks Request for Periodic ChecksDew Condensation Recording Before Calling Service PersonnelInstallation Function/OperationOther matters PlaybackDew caution sheet SpecificationsConnector section Accessories70971825 Limited Warranty