NAD Using the L 54’S Internal DVD Player Setup Menu, OSD Navigation, TV Aspect Ratio

Page 16

ENGLISH

FRANÇAIS

DEUTSCH NEDERLANDS ESPAÑOL

ITALIANO

РУССКИЙ

SVENSKA

Operation

USING THE L 54’S INTERNAL DVD PLAYER – SETUP MENU

OSD NAVIGATION

The L 54’s internal DVD player employs a simple, self-explanatory system of on-screen display “menus” that will appear on the connected video monitor/TV. These are required during the setup process (and are useful in day-to-day operation), so be sure to connect the monitor/TV before proceeding with setup.

DISPLAY THE SETup MENU

Press “SETUP/MEMORY” button on the front panel to display the L 54’s “Setup Menu” screen on your video monitor/TV. If the OSD does not appear, check your MONITOR OUT connections.

NAVIGATINg THE SETUP MENU OSD AND MAKING CHANGES

To navigate through the Setup Menu OSD options, please do the following using the HTR 4 (make sure to set the HTR 4’s Device Selector to DVD):

1Press keys to move up or down the menu selections.

2Use keys to select through the options of a particular menu.

3Press “ENTER” to save the settings.

To exit the Setup menu or from a menu option without saving, press the HTR 4’s “RTN” key or the front

panel’s SETUP/MEMORY button. You can also exit a menu option without saving by using the keys.

DISPLAY DISC OSD

You can display the general disc playback status on the TV screen. Some items can be changed using the menu. To use the on-screen display:

1Press DISPLAY during playback.

2Press to select an item. The selected item is highlighted.

3Press ENTER to change the setting. You can also use the number buttons if appropriate.

Notes

•The display feature may not be available for all disc media and is media dependent.

•The front panel and HTR 4’s “DISP” button toggles between time/track/chapters and subtitle/ angles/audio configuration (DVD only).

•If no button is pressed for about 10 seconds, the on-screen display disappears.

SETUP MENU

The Setup Menu allows one to customize the operation of the L 54. If the factory defaults do not suit your taste, you will need to use the setup menu to configure the L 54 yourself.

To access and navigate through the Setup Menu selections, please refer to and follow the directions stated in the above section about “Navigating the Setup Menu OSD and Making Changes.”

TV ASPECT RATIO

Select ‘4:3 LB’ or ‘4:3 PS’ when a standard 4:3 TV is connected.

4:3 LB Displays a wide picture with bands on the upper and lower portions of the screen.

4:3 PS Automatically displays the wide picture on the entire screen and cuts off the portions that do not fit.

16:9 Select when a 16:9 wide TV is connected.

TV SYSTEM

The ‘AUTO’ setting will detect automatically the media being played and display it. The other two settings, ‘NTSC’ and ‘PAL’, can be selected to force the output of the L 54 to the desired format. For example one can load a PAL media and display it in the NTSC format. Similarly one can load an NTSC media and display it in the PAL format.

Depending on the type of TV set you own, select the signal mode you wish to watch your disc. The default or Auto setting is PAL for Europe and NTSC for North America.

NOTE

Only NTSC is available for North America models.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents DVD Receiver Important Safety Instructions If the product has been exposed to rain or water Do not STARe Into BeamFCC Notice FCC WARNIngIf in Doubt ConSULT a Competent Electrician Important Information for UK CustomersModel no Serial no Table of Contents IntroductionUnpacking and Setup Getting the Most from the LQuick Start WHAT’S in the BOXAbout the L About the HTR 4 System Remote ControlEase of USE Identification of Controls Front PanelSCAN/TUNE Pressing momentarily the or button will Rear Panel Deutsch NederlandsIdentification of Controls Setup Setting UP the LFactory Default Settings Dealing with HUM and Noise Audio Mode Adjusting the Tone Controls About the ON-SCREEN Display OSD Displaying the L 54 DVD OSDAdjusting the Volume Adjusting the Subwoofer Level Trim on the FLYInput Select Dynamic Range Control DRCUsing the L OperationRegion Management Information About DVD/SVCD/VCD/CDUsing the L 54’S Internal DVD Player Setup Menu Setup MenuOSD Navigation TV Aspect RatioPassword LanguageSubtitle Down SamplingScan Screen SaverVideo OUT Divx CodeUsing the L 54’S Internal DVD Player Features Programming Playing MP3/WMA/JPEGRandom Play RepeatSetting Radio Preset About AntennasAssembling the Loop Antenna Selecting the RadioDeleting a Stored Preset Choosing FM MUTE/MODEAbout RDS Viewing RDS TextSpecifications Using the HTR 4 Remote ControlControlling the L Copy Command from Another Button Cancel OperationLearning Codes from Other Remotes PUNCH-THROUGHRecording Macros Macro CommandsExecuting Macros Button Illumination Timeout Factory ResetDelete Mode FlashesLoading Code Libraries Search ModeNAD-brand component Checking CODE-LIBRARY Number Summary of the HTR 4 ModesKey Device Key +RTN KeyReference TroubleshootingCondition Specifications AM SectionFM Section InputReference
Top Page Image Contents