NAD L 54 owner manual Loading Code Libraries, Search Mode, NAD-brand component

Page 27

Operation

USING THE HTR 4 REMOTE CONTROL

LOADING CODE LIBRARIES

The HTR 4 can store a different library of default NAD codes for each of its Device Selector “pages.” If the original default library does not control your NAD CD player, tape deck, DVD player, or other component, follow the procedure below to change the code-library.

Begin by ensuring that the component you wish the HTR 4 to control is plugged in and powered-up (“on,” not merely in standby). To enter the HTR 4’s Library Mode, simultaneously press-and-hold for 3 seconds both the desired Device Selector key and the [PROGRAM] key, until the Learn LED turns green.

While keeping the HTR 4 pointed toward the component, enter the first appropriate three-digit code-library number from the table below. If the component turns off, press [ENTER] to accept that code-library number and exit the Library Mode. If the component does not turn off, enter the next three-digit code-library number from the table.

When you enter the correct number the component will turn off; press [ENTER] to accept that code library number and exit the Library Mode.

NAD-brand component

HTR 4 code-library numbers

 

 

CD Player (new)

200

 

 

CD Player (old)

201

 

 

Tape Deck B

400

 

 

Tape Deck A

401

 

 

T562

600

 

 

T550, L55

601

 

 

T512, T531, T532

602

 

 

T571, T572

602

 

 

L56

604

 

 

T513, T533

605

 

 

SEARCH MODE

If none of the codes from the table, when entered, turns on the component, and if you are quite sure you have followed the above procedure completely and carefully, you may want to try the “search” method as follows:

Enter Library Mode by simultaneously pressing-and-holding for 3 seconds both the desired Device Selector key and the [PROGRAM] button until the Learn LED turns green. Now press-and-hold the HTR 4’s [] or []) key; the remote will step through all the available codes at a rate of approximately 1 per second.

When the component turns off, immediately release the cursor key; press [ENTER] to accept that code- library and exit the Library Mode. Try a few commands; should you prove to have stepped past the needed code-library, re-enter the Library Mode and use the cursor key to step back to it.

Note

It is possible that search mode will find code-libraries that operate, at least partially, some other brand (non-NAD) components. You may certainly exploit such capabilities as you find them. However, since we can only ensure the completeness or accuracy of NAD code-libraries, we cannot support the HTR 4’s operation with other-brand components.

ENGLISH

FRANÇAIS

ESPAÑOL NEDERLANDS DEUTSCH

ITALIANO

РУССКИЙ

SVENSKA

27

Image 27
Contents DVD Receiver Important Safety Instructions FCC WARNIng If the product has been exposed to rain or waterDo not STARe Into Beam FCC NoticeImportant Information for UK Customers If in Doubt ConSULT a Competent ElectricianModel no Serial no Introduction Table of ContentsWHAT’S in the BOX Unpacking and SetupGetting the Most from the L Quick StartAbout the HTR 4 System Remote Control About the LEase of USE Front Panel Identification of ControlsSCAN/TUNE Pressing momentarily the or button will Deutsch Nederlands Rear PanelIdentification of Controls Dealing with HUM and Noise SetupSetting UP the L Factory Default SettingsDisplaying the L 54 DVD OSD Audio ModeAdjusting the Tone Controls About the ON-SCREEN Display OSDDynamic Range Control DRC Adjusting the VolumeAdjusting the Subwoofer Level Trim on the FLY Input SelectAbout DVD/SVCD/VCD/CD Using the LOperation Region Management InformationTV Aspect Ratio Using the L 54’S Internal DVD Player Setup MenuSetup Menu OSD NavigationDown Sampling PasswordLanguage SubtitleDivx Code ScanScreen Saver Video OUTUsing the L 54’S Internal DVD Player Features Repeat ProgrammingPlaying MP3/WMA/JPEG Random PlaySelecting the Radio Setting Radio PresetAbout Antennas Assembling the Loop AntennaViewing RDS Text Deleting a Stored PresetChoosing FM MUTE/MODE About RDSUsing the HTR 4 Remote Control SpecificationsControlling the L PUNCH-THROUGH Copy Command from Another ButtonCancel Operation Learning Codes from Other RemotesMacro Commands Recording MacrosExecuting Macros Flashes Button Illumination TimeoutFactory Reset Delete ModeSearch Mode Loading Code LibrariesNAD-brand component Device Key +RTN Key Checking CODE-LIBRARY NumberSummary of the HTR 4 Modes KeyTroubleshooting ReferenceCondition Input SpecificationsAM Section FM SectionReference