NAD L 54 owner manual Identification of Controls

Page 11

Identification of Controls

REAR PANEL

7DIGITAL INPUTS, OPTICAL & COAXIAL : Connect to the coaxial/ optical S/PDIF-format digital output of sources such as VCRs, HDTV, satellite tuners or other components. Connect OPTICAL/COAXIAL DIGITAL INPUT to an S/PDIF-format digital output. We recommend your source material be set to PCM 2-channel format for these digital inputs.

8DIGITAL OUTPUT, OPTICal : Connect the OPTICAL DIGITAL OUTPUT port to the corresponding S/PDIF digital input of a recording component such as a CD recorder, DAT deck or computer soundcard.

9COMPONENT VIDEO OUT : Connect the L 54’s “COMPONENT VIDEO OUT” to the component video input of a compatible video monitor/TV. Be sure to observe consistency in connecting the appropriate Y, Cb/Pb, Cr/Pr jacks to the corresponding sources/inputs. Do not rely purely on the color coding of the jacks, which may not always be consistent among brands. The routing of the component video output is fixed.

The L 54’s component-video output is a fully wide-band output, compatible with all HDTV formats. On-screen display menu is also shown at component video output.

Notes

•Make sure to set ‘VIDEO OUT’ to ‘COMPONENT’ at the SETUP menu for video to be available at Component Video OUT. See also section VIDEO OUT” at “Setup Menu” discussion.

•“COMPONENT VIDEO OUT” jack will only display the internal DVD video signals.

10AC POWER CORD : Connect AC power cord to the voltage according to the model, 120V for US and 230V for Euro models.

The clock resets to “00:00” when the AC power cord is unplugged and then plug-in again to the power source.

11SWITCHEd AC OUTLET : This convenience jack can supply switched power to another component or accessory. It is powered on and off by the front panel POWER button (or the HTR 4’s ON and OFF buttons).The total draw of all devices connected to this jack must not exceed 100 watts.

12SCART/RGB OUT (Euro model/PAL only) : Connect the L 54’s “SCART/RGB OUT” to the SCART/RGB video input of a compatible video monitor/TV. Be sure to observe the correct orientation of the SCART/ RGB plug. Make sure also to set ‘VIDEO OUT’ to ‘RGB’ at the SETUP menu for stable video availability at SCART/RGB OUT.

13MONITOR OUT : Connect to video input of the monitor/television, using quality RCA and/or S-Video cables designed for video signals. In general, the S-Video connection is superior and should be used if your TV/monitor provides the corresponding input.

Make sure also to set ‘VIDEO OUT’ to ‘S-Video’ at the SETUP menu for video to be available at ‘S-Video’ Monitor OUT.

ENGLISH

FRANÇAIS

ESPAÑOL NEDERLANDS DEUTSCH

ITALIANO

РУССКИЙ

SVENSKA

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents DVD Receiver Important Safety Instructions FCC WARNIng If the product has been exposed to rain or waterDo not STARe Into Beam FCC NoticeModel no Serial no Important Information for UK CustomersIf in Doubt ConSULT a Competent Electrician Introduction Table of ContentsWHAT’S in the BOX Unpacking and SetupGetting the Most from the L Quick StartEase of USE About the HTR 4 System Remote ControlAbout the L Front Panel Identification of ControlsSCAN/TUNE Pressing momentarily the or button will Deutsch Nederlands Rear PanelIdentification of Controls Dealing with HUM and Noise SetupSetting UP the L Factory Default SettingsDisplaying the L 54 DVD OSD Audio ModeAdjusting the Tone Controls About the ON-SCREEN Display OSDDynamic Range Control DRC Adjusting the VolumeAdjusting the Subwoofer Level Trim on the FLY Input SelectAbout DVD/SVCD/VCD/CD Using the LOperation Region Management InformationTV Aspect Ratio Using the L 54’S Internal DVD Player Setup MenuSetup Menu OSD NavigationDown Sampling PasswordLanguage SubtitleDivx Code ScanScreen Saver Video OUTUsing the L 54’S Internal DVD Player Features Repeat ProgrammingPlaying MP3/WMA/JPEG Random PlaySelecting the Radio Setting Radio PresetAbout Antennas Assembling the Loop AntennaViewing RDS Text Deleting a Stored PresetChoosing FM MUTE/MODE About RDSControlling the L Using the HTR 4 Remote ControlSpecifications PUNCH-THROUGH Copy Command from Another ButtonCancel Operation Learning Codes from Other RemotesExecuting Macros Macro CommandsRecording Macros Flashes Button Illumination TimeoutFactory Reset Delete ModeNAD-brand component Search ModeLoading Code Libraries Device Key +RTN Key Checking CODE-LIBRARY NumberSummary of the HTR 4 Modes KeyCondition TroubleshootingReference Input SpecificationsAM Section FM SectionReference
Top Page Image Contents