NAD L 54 owner manual Using the HTR 4 Remote Control, Specifications, Controlling the L

Page 23

Operation

USING THE HTR 4 REMOTE CONTROL

SPECIFICATIONS

• Controls up to 8 devices.

• 44 function keys.

•Learns up to 352 commands.

•Records up to 44 macros with a maximum of 64 commands each.

• Configurable punch-through.

•Key illumination with programmable timeout.

• Upgradable.

•Contains pre-programmed library of NAD remote codes.

The NAD HTR 4 is ready to operate the L 54 right out of the box, but it is really eight remotes in one. Each of the 8 Device Selector keys at the top of the handset can call up a new “page” of remote control codes to be transmitted by the remaining 44 keys. You may “teach” codes from any infrared-remote controlled component, regardless of brand, to any or all of these.

Obviously, the most logical system is that you teach the codes from your DVD player to the [DVD] Device Selector “page,” your television’s codes to the [TV] “page,” and so on, but there is no required scheme: You may load any commands to any key on any page (see “Learning Codes From Other Remotes,” below).

The HTR 4 is already preprogrammed with a full complement of commands for the L 54 on its [AMP] Device Selector page, and as well as with library commands to operate most NAD-brand DVD

or CD components on the corresponding Device Selector “pages.”These default commands are permanent: Even if you teach the HTR 4 new commands to take their place, the underlying library commands remain in place and can easily be recalled should you add an NAD component to your system later (see “Delete Mode”, below).

Note: For use with the L 54, it should not be necessary to re-program any keys on the HTR 4 [AMP] page. However, in order for the HTR 4 to control your specific NAD-brand components you may need to load one or more different code-libraries (see “Loading Code Libraries,” below).

CONTROLLING THE L 54

The HTR 4 is divided into two main sections. Eight Device Selector keys at the top—[AMP], [DVD,] [TV,] and so on—set the handset’s remaining keys to a “page” of commands to control a particular component. A Device Select key determines only what component the HTR 4 will command; it does not perform any function on the L 54. All of the remaining keys are function keys that can “learn” control codes from virtually any infrared remote controller, allowing you to teach the codes of your equipment, regardless of brand, to the HTR 4.

However, the HTR 4 is already preprogrammed to operate the L 54. All of the function keys on the [AMP] Device Selector “page” perform L 54 functions. (The HTR 4 can also command many other NAD components, from its [DVD,] [CD,] [TUNER,] and [CUSTOM] pages.)

It is important to note that certain HTR 4 keys perform different functions depending on the selected Device Selector “page.”The color of the Device Selector key-labeling corresponds to the labeling of the function keys. Most centrally, the orange [AMP] Device Selector “page” corresponds to the orange input-select labeling above the numeric keys: When the HTR 4’s [AMP] Device Selector page is active, these keys select the Receiver inputs. Similarly, the purple [DVD] Device Selector “page” corresponds to several purple labels, the green [TV] page to green labels, and so on.

ENGLISH

FRANÇAIS

ESPAÑOL NEDERLANDS DEUTSCH

ITALIANO

РУССКИЙ

SVENSKA

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents DVD Receiver Important Safety Instructions FCC WARNIng If the product has been exposed to rain or waterDo not STARe Into Beam FCC NoticeModel no Serial no Important Information for UK CustomersIf in Doubt ConSULT a Competent Electrician Introduction Table of ContentsWHAT’S in the BOX Unpacking and SetupGetting the Most from the L Quick StartEase of USE About the HTR 4 System Remote ControlAbout the L Front Panel Identification of ControlsSCAN/TUNE Pressing momentarily the or button will Deutsch Nederlands Rear PanelIdentification of Controls Dealing with HUM and Noise SetupSetting UP the L Factory Default SettingsDisplaying the L 54 DVD OSD Audio ModeAdjusting the Tone Controls About the ON-SCREEN Display OSDDynamic Range Control DRC Adjusting the VolumeAdjusting the Subwoofer Level Trim on the FLY Input SelectAbout DVD/SVCD/VCD/CD Using the LOperation Region Management InformationTV Aspect Ratio Using the L 54’S Internal DVD Player Setup MenuSetup Menu OSD NavigationDown Sampling PasswordLanguage SubtitleDivx Code ScanScreen Saver Video OUTUsing the L 54’S Internal DVD Player Features Repeat ProgrammingPlaying MP3/WMA/JPEG Random PlaySelecting the Radio Setting Radio PresetAbout Antennas Assembling the Loop AntennaViewing RDS Text Deleting a Stored PresetChoosing FM MUTE/MODE About RDSControlling the L Using the HTR 4 Remote ControlSpecifications PUNCH-THROUGH Copy Command from Another ButtonCancel Operation Learning Codes from Other RemotesExecuting Macros Macro CommandsRecording Macros Flashes Button Illumination TimeoutFactory Reset Delete ModeNAD-brand component Search ModeLoading Code Libraries Device Key +RTN Key Checking CODE-LIBRARY NumberSummary of the HTR 4 Modes KeyCondition TroubleshootingReference Input SpecificationsAM Section FM SectionReference
Top Page Image Contents