Alpine IVA-W502E Playing a Disc, To display the DVD mode screen, If a menu screen appears, 18-EN

Playing a Disc

IVA-W502E has a built-in DVD player. When an optional Alpine DVD/ Video CD/CD player (or DVD changer) is connected to the IVA- W502E, you can control it from the IVA-W502E (except some operations).

WARNING

It is dangerous (and illegal in many states) for the driver to watch the DVD/TV/Video while driving the vehicle. The driver may be distracted from looking ahead and an accident could occur.

Install the IVA-W502E correctly so that the driver cannot watch DVD/TV/Video unless the vehicle is stopped and the emergency brake is applied.

If the IVA-W502E is not installed correctly, the driver will be able to watch the DVD/TV/Video while driving the vehicle and may be distracted from looking ahead causing an accident. The driver or other people could be severely injured.

To display the DVD mode screen

•If you try to activate the auxiliary device while driving, the display will show the warning-PICTURE OFF FOR YOUR SAFETY.

Caution

•Not all functions will operate for every DVD. See the individual DVD’s instructions for details on the features supported.

•Fingerprints on a disc may adversely affect playback. If a problem occurs, remove the disc and check for fingerprints on the playback side. Clean the disc if necessary.

•If you switch the power or Ignition key OFF or change sources during playback, playback will continue where you left off when you resume playback.

•If you try to perform an invalid operation (based on the type of disc being played), the following mark is displayed on the monitor screen:

•Play Position Memory Function

Even if you turn power off or switch the Ignition key to OFF during playback or change the source, playback will continue from the point where playback stopped when the power is turned ON again.

1 Touch [SOURCE] on the main source screen.

The SOURCE selection screen is displayed.

2 Touch [DISC].

The display shows the DISC mode screen.

Insert a disc with the label side facing up. The unit starts to play the disc.

When an optional Alpine DVD player is connected: Insert a disc into the DVD/Video CD/CD player, the player starts playing.

•The operation screen changes to the visual screen in the DVD or Video CD mode for 5 seconds after an operation has been performed. Touch the display panel to display the operation screen again.

•The display mode can be changed by touching [WIDE]. For operation, see “Switching Display Modes” on page 26.

To eject the disc

Press OPEN.

•The reverse side of a double-sided DVD will not be played automatically.

Remove the disc, turn it over, and reinsert it.

•Do not insert discs containing maps for the navigation system. Doing so could result in damage.

•Refer also to “DVD Setup” (pages 27 to 32).

•Be sure the remote input lead is connected to the remote output lead of this unit when a DVD changer or DVD player is connected. If not correctly connected, touch operation cannot be performed.

•To return to the previous screen during Video CD playback (when PBC is set to ON), touch [] after touching [P1/2] of the function guide. However, the function may vary depending on the disc.

•“CAN’T DOWNMIX” is displayed when a Downmix (multi-channel signals are mixed into 2ch) prohibited section of a DVD-Audio disc is played. In this case, only the Lch/Rch recorded on the disc is output as sound. (The sound of Centre speaker, L-surround speaker, R- surround speaker, and Subwoofer is not output.)

•While “INDEX READING” is displayed by DivX®, the fast- forwarding/fast-reversing and repeat functions, etc. cannot be used.

If a menu screen appears

On DVDs and Video CDs with playback control (PBC), menu screens may appear automatically. If this happens, perform the operation described below to start playback.

•To play back a DVD-Audio disc, set “VCAP” in “Setting of the DVD- Audio Playback Mode” (page 31).

Direct Menu Operations

1 Touch the DVD menu directly.

•Some operations cannot be performed depending on the disc.

18-EN