Aiwa XD-SPM823 operating instructions Specifications, Ntsc

Specifications

Power supply	120 V AC, 60 Hz
Power consumption	16 W
Power consumption in standby mode
	1.4 W
Weight	5.7 kg (12.9 lbs)
External dimensions	430 ⋅ 118 ⋅ 414 mm
	(17 ⋅ 4.7 ⋅ 16.3 inches)
	(w ⋅ h ⋅ d)
Laser	Semiconductor laser, wavelength:
	650/780 nm
Signal format	NTSC
Supported discs	DVD video discs: 12 cm (single-
	sided single layer, single-
	sided double layer, double-
	sided double layer), 8 cm

(single-sided single layer, single-sided double layer, double-sided double layer)

Compact discs (CD-DA, MP3): 12 cm and 8 cm

Component video output

Y output: 1.0 Vp-p

(75 ohms, sync negative) PR/CR, PB/CB outputs: 0.7 Vp-p

(75 ohms)

RCA jacks (CR/CB/Y) ⋅ 1

S-video output Y output: 1.0 Vp-p (75 ohms, sync negative)

C output: 0.3 Vp-p

4-pin mini DIN jack ⋅ 1

Composite video output

1.0Vp-p (75 ohms, sync negative)

RCA jack ⋅ 1

Audio outputDigital output: 0.5 Vp-p (75 ohms), RCA jack ⋅ 1

0.5Vp-p (75 ohms), Fiber optical connector ⋅ 1

Analog output: 2.0 Vrms

(1 kHz, 0 dB, 330 ohms), RCA jacks (L/R) ⋅ 1

Audio output characteristics

Signal-to-noise ratio: More than 95 dB (EIAJ)

Dynamic range: More than 90 dB (EIAJ)

Harmonic distortion: 0.008% Frequency response:

CD: 4 Hz to 20 kHz

DVD: 4 Hz to 22 kHz (48-kHz sampling), 4 Hz to 44 kHz (96-kHz sampling)

Operating temperatures

5˚C to 35˚C (41˚F to 95˚F)

AccessoriesVideo cord (1) Audio cord (1) Remote control (1) Operating instructions

Specifications are subject to change without notice.

58 ENGLISH

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Modifications or adjustments to this product, which are not expressly approved by the manufacturer, may void the user’s right or authority to operate this product.

•Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. ©1992-1999 Dolby Laboratories. All rights reserved.

•"DTS" and "DTS Digital Out" are trademarks of Digital Theater Systems, Inc.