Controlling a TV with the Remote

(DVD-S321 only)

The remote can also be set up to control most TVs. To program the remote, use the code

Troubleshooting

Before requesting service (troubleshooting), please check the following.

that corresponds to your brand.

TV Codes

Code	Brand	Code	Brand
01	SAMSUNG_1	16	SHARP_1
02	SHARP_2	17	ZENITH
03	SONY	18	LG_3
04	MAGNAVOX	19	DAEWOO_8
05	SANYO_1	20	SANYO_2
06	LG_2	21	EMERSON
07	RCA	22	SHARP_3
08	LG_1	23	SAMSUNG_4
09	TOSHIBA	24	PANASONIC_2
10	HITACHI	25	NOBLEX
11	JVC	26	TELEFUNKEN
12	PANASONIC_1	27	NEWSAN
13	MITSUBISHI_2	28	LOEWE
14	SAMSUNG_2	29	RCA2
15	SAMSUNG_3

Problem

No operations can be performed with remote.

Disc does not play.

5.1channel sound is not being reproduced.

The	icon appears on
screen.

Disc Menu doesn’t appear.

Play mode differs from the Setup Menu selection.

The screen ratio cannot be changed.

Action

•	Check the batteries in the remote. May need replacing.
•	Operate the remote control at a distance of no more than 20 feet.
•	Remove batteries and hold down one or more buttons for several
	minutes to drain the microprocessor inside the remote to reset it.
	Reinstall batteries and try remote again.
•	Ensure that the disc is installed with the label side facing up.
•	Check the region number of the DVD.
•	5.1 channel sound is reproduced only when the following conditions
	are met. :
	1) The DVD player is connected with the proper amplifier
	2) The disc is recorded with 5.1 channel sound.
•	Check whether the disc being played has the “Dolby 5.1 ch” mark on
	the outside.
•	Check if your audio system is connected and working properly.
•	In a SETUP Menu, is the Audio Output set to Bitstream?
•	The features or action cannot be completed at this time because:
	1. The DVD’s software restricts it.
	2. The DVD’s software doesn’t support the feature (e.g., angles).
	3. The feature is not available at the moment.
	4. You’ve requested a title or chapter number or search time that is
	out of range.
•	Check if the disc has a Menu.
•	Some of the functions selected in the Setup Menu may not work
	properly if the disc is not encoded with the corresponding function.
•	The Screen Ratio is fixed on your DVDs.

Page

P20

P23

P40~41

P40~45

P45

1 Turn on the TV

2 Point the DVD’s remote at the TV.

3 While holding the TV POWER button down, enter the code for your brand.

e.g For Samsung_1 TVs

4 If the TV turns off, setup is complete.

Enter other codes of the same brand if the first code does not work.

5 To operate the TV, use the “TV Function Buttons” described on page 19.

NOTE

No audio.

Forgot password

If you experience other problems.

•	Make sure you have selected the correct Digital Output in the Audio
	Options Menu.
• Press power on from a cold start with no disc in the unit. Press the STOP
	and PLAY buttons simultaneously on the front panel for three seconds. The
	Select Menu Language display will appear. Select the desired language
	button. Press the SETUP button on the remote control to select the Parental
	Mode. The Parental Mode is now unlocked as indicated on the display.
	Press the DOWN button to select Parental. Press ENTER and the Create
	Password display will appear. You can now set your rating level and
	change your password to a new number.
•	Go to the contents and find the section of the instruction book that
	contains the explanations regarding the current problem, and follow
	the procedure once again.

P44

P43

While holding down the TV POWER button,	The remote may not be able to control every
enter 0 and then 1.	model TV of the brands listed.

• If the problem still cannot be solved, please contact your nearest

authorized service center.

REFERENCE