Toshiba 52HMX94 Connecting a VCR and satellite receiver, Three coaxial cables, Source on the TV

Chapter 2: Connecting your TV

Connecting a VCR and satellite receiver

Note: The TV Guide On Screen™ system does not receive program listings from or for any satellite service.

You will need:	From
￿ three coaxial cables	antenna
￿ one set of component video cables (if your
satellite receiver does not have component
video, connect the standard A/V cables only)
￿ three sets of standard A/V cables

Stereo VCR

		VIDEO
IN from ANT	CH 3	L	R	IN
	CH 4
OUT to TV		L	R	OUT

• For better picture performance, if your satellite

receiver and VCR have S-video, connect S-video

cables (plus the audio cables) instead of the standard

video cables. Do not connect both types of video

cable to VIDEO 1 (or VIDEO 2) at the same time or

the picture performance will be unacceptable.

• If you have a mono VCR, connect L/MONO on the

TV (VIDEO 1) to your VCR’s AUDIO OUT jack using

the white audio cable only.

￿ To view satellite programs using the

TV

OUT 1	S-VIDEO	S-VIDEO
		Y	Y
OUT 2			PB
TheaterNet

VIDEO PR

L/	L/
	MONO

AUDIO

AUDIO

			TheaterNet	CableCARD™
			IEEE1394
				EJECT
		ANT1	1
IN		(CABLE)
			2
AUDIO
R	L		HDMI IN
2			2
		ANT2

1 ANT (75 )

	1
VIDEO
L/
MONO
AUDIO	G-LINK

component video connections:

RR

R

COLOR COLOR

R

VIDEO 2 STREAM STREAM

Select the ColorStream HD-1 video input From

IN

HD-1 HD-2

OUTDIGITAL AUDIO OUT

source on the TV.*	satellite
￿ To view satellite programs using the standard	dish

video connections or to record satellite programs:

Y PB PR

Satellite

IN

S-VIDEO COMPONENT VIDEO	VIDEO
OUT	OUT

AUDIO L OUT L

R R

Turn on all three devices. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details). Select the VIDEO 2 video input source on the TV.*

￿ To view the VCR or view and record antenna channels:

Turn ON the VCR. Select the ANT-1 video input source on the TV.*

Tune the TV to channel 3 or 4 (whichever channel is vacant in your area).

or... Turn ON the VCR. Tune the VCR to the channel you want to watch. Select the VIDEO 1 video input source on the TV.*

_____________

*To select the video input source, press INPUT on the remote control (see page 66). To program the TV remote control to operate other devices, see Chapter 3.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Satellite receiver

Note: The VIDEO/AUDIO OUT jacks output the signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the appropriate input mode is selected.

￿To use the TV Guide On Screen recording features:

1.Connect the G-LINK cable according to the instructions on page 25.

2.Make sure the VCR is connected to the A/V OUT jacks on the TV (see illustration).

3.Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4.See Chapter 5 for details on setting up the TV Guide On Screen system.

5.See Chapter 7 for details on using the TV Guide On Screen system.

		Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.	15
HMX94(E)012-25(2B-Cnct)	15	9/28/04, 1:34 PM

(E) 46/52/62HM94