Toshiba 52HMX94 owner manual Appendix, Lamp unit replacement and care, Replacing the lamp unit

Page 98

11 Appendix

Lamp unit replacement and care

Replacing the lamp unit

(User-replaceable component)

WARNING: RISK OF

ELECTRIC SHOCK!

TO REDUCE THE RISK OF ELECTRIC SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS SPECIFIED HEREIN. REFER ALL SERVICING NOT SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE PERSONNEL. Failure to follow this WARNING may result in death or serious injury.

The light source for this TV is a mercury lamp with internal atmospheric pressure that increases during use. The lamp has a limited service life that varies depending on product use and user settings.

As is generally the case with all projection TVs that use projection lamps as a light source, the brightness of the lamp in this TV may vary somewhat over the expected service life and will generally decrease over time. The average useful service life for the lamp is approximately 8,000 hours in LOW POWER mode or 6,000 hours in HI BRIGHT mode. See “Selecting the Lamp mode” on page 72 for information on switching the lamp mode. Because these are averages, some lamps will require earlier replacement.

Note : The lamp is warranted only for the periods and to the extent set forth in the Limited Warranty applicable to this set, which is a substantially shorter period of time than the average useful service period. See “Limited United States Warranty” on page 102 or “Limited Canada Warranty” on page 103, as applicable.

If you use the lamp beyond its service life:

you may notice a reduction in the colors and/or brightness of the picture; and

the strength of the quartz glass in the lamp will be reduced and the lamp may rupture (often making a loud noise when this happens). If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

Note: The lamp unit is designed so broken lamp glass remains securely inside the lamp unit.

CAUTION: Always handle the lamp unit with care.

The lamp unit in this TV was designed for safe replacement by consumers; however, if the lamp unit is subjected to intentional abuse, the unit may break, exposing sharp edges or pinch points.

When to replace the lamp unit

You should replace the lamp unit:

if the picture darkens and/or colors fade;

if the screen (lamp) does not light (LED indication #3, page 94); or

if you hear a loud noise and the picture goes black, which may indicate a lamp rupture (LED indication #3, page 94).

To obtain a replacement lamp unit:

In the U.S.:

 

Web

Contact

In warranty

www.tacp.toshiba.com/service

Call toll-free

1-800-631-3811.

 

 

 

 

 

Out of

www.ceaccessories.toshiba.com

Consult your

warranty

 

consumer

 

electronics dealer

 

 

 

 

for availability.

 

 

 

In Canada:

Contact a Toshiba parts distributor by directing your web browser to www.toshiba.ca. Click ÒHome Entertainment,Ó and then click ÒSupport.Ó

Use the replacement lamp unit model listed below only. Using any other lamp may cause damage to the TV and/or lamp.

CAUTION: Always replace with same

type lamp unit: Model No. TB25-LMP (Stock no. 23311083)

98

 

Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.

 

 

HMX94(E)098-105(11-App)

98

9/28/04, 11:08 AM

(E) 46/52/62HM94

Image 98
Contents 52HMX94 62HMX94 62HMX94 Safety PrecautionsDisposal of mercury may be regulated due to For replacement of the obsolete outlet Important Safety InstructionsInstallation, Care, and Service DAMAGE! Never place the TV onService life Frequent or continuous, unplug the power cordLength of service life varies depending on product See Lamp unit replacement and care on pages 98-100. NoteContents Using the TV Guide On Screen 106Welcome to Toshiba Features of your new TVIntroduction See Important notes about yourEnter TV off or on, press this button to reset the TV Connecting your TVPower is OFF. This is called standby mode TV front touchpad and side panel controls and connectionsTV back panel connections For an explanation of cable types, seeOverview of cable types To a Personal Computer PCTo view encrypted digital channels For more information, call your local cable operatorYou will need To use the TV Guide On Screen recording features Connecting a VCR and antenna or Cable TV no Cable boxConnecting a camcorder To view the VCRTo view basic and premium Cable channels Connecting a VCR and Cable boxOn Screen recording features From Cable TVSelect the ColorStream HD-1 video input Connecting a VCR and satellite receiverThree coaxial cables Source on the TVTo view VCR To view premium Cable channelsTo view the DVD player From antenna or Cable To view antenna or Cable channelsTo record a TV program while watching a DVD To dub or edit from VCR 1 to VCR Connecting two VCRsTo view the antenna or Cable signal To connect an Hdmi device, you will need Connecting an Hdmi or a DVI device to the Hdmi inputOne Hdmi cable type a connector for each device To connect a DVI device, you will needOne optical audio cable Connecting a digital audio systemConnecting an analog audio system To control the audioTo control the devices TheaterNet on-screen device controlTo connect the IR blaster cable Supported signals Connecting IEEE-1394 video devicesUsing analog-compatible IEEE-1394 devices Using TheaterNet on-screen device controlOther networked IEEE-1394 devices, if any, When you connect a D-VHS or Avhd device to the TVYou can connect an IEEE-1394 compatible D-VHS or Avhd Audio/video hard drive digital recorder such as Toshiba’sIEEE-1394 device management To edit the IEEE-1394 device informationTo connect to the G-LINK jack For details on setting up the TV Guide On Screen systemLINKconnection See ChapterSleep accesses the sleep timer Using the remote controlLearning about the remote control 51/57/65H94Device mode control after programming Installing the remote control batteriesTo install the remote control batteries Remote Control functional key chart PowerAudio VCR Mute Press Mode to select the mode you want to set up Device code setupPress Mode to select the TV mode to control the TV Searching and sampling the code of a deviceRepeatedly press Mode to select CABLE/SAT mode Using the volume lock featureOperational feature reset To reset the volume controls to the original device modeCable boxes Multi-brand remote control device codesVCRs/PVRs Laser disks CD playersReceivers DVD playersMenu layout and navigation Main menu layoutSetup / Installation menu layout Navigating the menu systemTo set up the TV Guide On Screen system TV Guide On Screen system setupConfiguring the location of your TV Setting up the TV Guide On Screen system On nextHMX94E036-395-TVGsetup 27/04, 1044 AM TV Guide On Screen Reminder To configure the ANT 1 and ANT 2 input sources Setting up your TVConfiguring the antenna input sources Selecting the menu languageTo program channels automatically Programming channels into the TV’s channel memoryProgramming channels automatically Manually adding and deleting channels in the channel memory To clear your favorite channel lists Programming your favorite channelsTo add and delete channels in the Favorite Channels lists To tune your favorite channels for the current ANT inputTo set up TheaterNet device control Setting up and using TheaterNet on-screen device controlSetting up TheaterNet To remove a device from TheaterNetTo view another source To select the device’s control icons directlyTo close the on-screen control icons Laser disk players TheaterNet IR device codesAmplifiers Miscellaneous audio devicesVideo accessory Hdtv decoder Receivers VCRsSTS To select the Hdmi audio mode Setting the Hdmi audio modeSetting the time and date To set the Avhd device skip timeViewing the CableCARD menu Setting the Quick Restart featureTo set the Quick Restart feature To view the CableCARD menuViewing the system status Viewing the digital signal meterRestore Factory Defaults Using the TV Guide On Screen interactive program guide To open the TV Guide On Screen systemTV Guide On Screen remote control functions Navigating the TV Guide On Screen systemLock/unlock icon indicates the status of the Video Window Video WindowPanel Menus To lock/unlock the Video Window¥ Show is presented in high-definition TV, if available Info BoxTV Guide On Screen Icons Episode Options panel menu TV Guide On Screen ServicesListings screen Search screen Example Category searchTo edit or delete a keyword Example Keyword searchList of all matching shows for that keyword is displayed To view a recording, you can do one of the following Recordings screenTo choose the way recordings are displayed Screen a Screen BSchedule screen Record featuresSet a show to Record from a panel menu Record conflict Manually set a show to RecordRecording notification banner Record iconsManually set a show Reminder Remind featuresSet a show Reminder from a panel menu Remind icons Reminder notification bannerRemind conflict Change channel display Setup screenChange system settings Record defaults Change default optionsGeneral default options Remind defaultsTo select the video input source to view Using the TV’s featuresSelecting the video input source to view Channel zyTo clear the input labels Labeling the video input sourcesTo label the video input sources Switching between two channels using Channel Return Tuning channelsTuning to the next programmed channel Switching between two channels using SurfLockNatural picture size Press PIC Size on the remote controlSelecting the picture size To select the picture sizeTheaterWide 2 picture size for letter box programs None of the picture is hiddenTheaterWide 1 picture size For 43 format program Full picture size for 169 480i, 480p source programs onlyTo turn on the Auto Aspect feature Using the auto aspect ratio featureTo set the scroll settings To turn off the Auto Aspect featureTo set the Cinema Mode to Video Selecting the lamp modeTo set the Cinema Mode to Film To select the lamp modeTo display a program in the POP window Using the POP featuresUsing the POP double-window feature To close the POP windowTo close the still POP window Switching the speaker audio main or POPFreezing the main picture in the POP double-window To scan and tune your favorite channels Using the favorite channel scan featurePOP double-window aspect ratio Adjusting the picture quality Adjusting the pictureSelecting the picture mode Resetting the picture settingsResetting the advanced picture settings Using CableClear DNR digital noise reductionSelecting the color temperature Digital closed captions Using the closed caption modeAdvanced closed captions Digital audio selector Adjusting the audioMuting the sound Selecting stereo/SAP broadcastsUsing the StableSound feature Turning off the built-in speakersUsing the SRS WOW surround sound feature Selecting the optical audio output format3V memory card Using the memory card Jpeg picture viewer/MP3 audio playerMemory card specifications Press Using the Jpeg picture viewerTo view digital photos on your TV During the slide showTo close the picture viewer Using the MP3 audio playerTo set the slide show interval To close the picture viewer and remove the memory cardUsing the memory card Jpeg picture viewer/MP3 audio player Using the Game Mode featureUsing the MP3 audio player contnued Memory card care and handlingSetting the ON/OFF timer Setting the sleep timerUnderstanding the last mode memory feature Displaying TV setting information on-screenUnderstanding the auto power off feature Chip rating status Picture size Lamp modeIf you cannot remember your PIN code Using the Locks menuEntering the PIN code Changing your PIN codePress z to highlight Edit Rating Limits and press Blocking TV programs and movies by rating V-ChipTo block and unblock TV programs and movies Edit Rating Limits screen below appearsLocking video inputs Blocking channelsUnlocking programs temporarily Using the GameTimer Using the front panel lock featureTroubleshooting Closed caption problems Set to SAP modeRestore Factory Defaults procedure as described on Caption featureLED indications TV Guide On Screen FAQs SetupWhy aren’t all my channels initially displayed? How do I resize or close the Info window? OperationsAppendix Lamp unit replacement and careWhen to replace the lamp unit Replacing the lamp unitHow to replace the lamp unit Grasp the lamp unit handle and gently pull the lamp unitReplace the thumb screw and hand-tighten U.S., call Customer Service atDisposing of the used lamp unit Specifications Television SystemLimited United States Warranty For DLP Television ModelsLimited Canada Warranty Products Purchased in Canada and Used in the U.S.A. are104 105 Index Picture-out-picture POP Picture adjustmentsRemote control 32-33Toshiba America Consumer PRODUCTS, L.L.C 04-11 R1