Toshiba 52HMX94 owner manual Connecting an Hdmi or a DVI device to the Hdmi input

Chapter 2: Connecting your TV

Connecting an HDMI™ or a DVI device to the HDMI input

The HDMI[1] input on your TV receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI[2] device.

This input is designed to accept HDCP[3] program material in digital form from EIA/CEA-861/861B–compliant[4]consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output).

The HDMI input is designed for best performance with 720p and 1080i high-definition video signals, but will also accept and display 480i and 480p signals.

NOTE: NEVER CONNECT THIS TV

TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

To connect an HDMI device, you will need:

• one HDMI cable (type A connector) for each device

For proper operation, it is recommended that you use as short an HDMI cable as possible. You should not encounter difficulty if you use an HDMI cable shorter than 16.4 ft (5m).

HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration below). Some CDVs (video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables. However, if you connect analog audio cables with this connection, the HDMI terminal on the TV will not receive the HDMI digital audio signal and you will hear analog audio only.

See “Setting the HDMI audio mode” on page 49.

HDMI device

HDMI OUT

VIDEOAUDIO

L R IN

L ROUT

___________

[1]HDMI = High-Definition Multimedia Interface.

[2]DVI = Digital Video Interface.

[3]HDCP = High-bandwidth Digital Content Protection.

[4]EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.

NOTE: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

•When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device.

•When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV.

To connect a DVI device, you will need:

•one HDMI-to-DVI adapter cable (HDMI type A connector) for each device

For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

• one pair of standard analog audio cables

An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration below).

See “Setting the HDMI audio mode” on page 49.

DVI device

VIDEO	AUDIO	DVI/HDCP
		OUT

L R IN

L ROUT

TV

TV

OUT 1

OUT 2

TheaterNet

		TheaterNet	CableCARD™
		IEEE1394
			EJECT
		1
		ANT1
IN		(CABLE)
		2
AUDIO
R	L	HDMI IN

				2		2
S-VIDEO	S-VIDEO				ANT2
		Y	Y	1	ANT (75 )
		PB	PB			1
VIDEO	VIDEO	PR	PR	VIDEO	VAR
					AUDIO
				L/
L/	L/
MONO	MONO	L	L	MONO	L
AUDIO	AUDIO	AUDIO	AUDIO	AUDIO		G-LINK
		R	R
R	R			R	R
VIDEO 1	VIDEO 2	COLOR	COLOR
		STREAM	STREAM
		HD-1	HD-2	OUT		DIGITAL
	IN

AUDIO OUT

OUT 1

OUT 2

TheaterNet

					TheaterNet	CableCARD™
					IEEE1394
						EJECT
				ANT1	1
			IN	(CABLE)
					2
			AUDIO
					HDMI IN
			2		2
S-VIDEO	S-VIDEO			ANT2
	Y	Y	1	ANT (75	)

		PB	PB		1
VIDEO	VIDEO	PR	PR	VIDEO	VAR
					AUDIO
				L/
L/	L/
MONO	MONO	L	L	MONO	L
AUDIO	AUDIO	AUDIO	AUDIO	AUDIO	G-LINK
		R	R
R	R			R	R
VIDEO 1	VIDEO 2	COLOR	COLOR
		STREAM	STREAM
		HD-1	HD-2	OUT	DIGITAL
	IN

AUDIO OUT

___________

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

		Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.	19
HMX94(E)012-25(2B-Cnct)	19	9/28/04, 1:34 PM

(E) 46/52/62HM94