Toshiba 62HMX84, 52HMX84 Adding channels to the TV’s memory, Programming channels automatically

Page 27

Adding channels to the TV’s memory

When you press Channel y or z, your TV will stop only on the channels stored in the TV’s channel memory.

Follow the steps below and on the next page to program all active channels into the TV’s memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are stored automatically, you can manually add or erase individual channels (see page 28).

To program channels automatically:

Note:

To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

Introduction

Connecting	yourTV

1.Press MENU, and then press x or • until the SET UP menu appears.

2.Press y or z until TV/CABLE is highlighted, and then press ENTER to display the pull-down menu.

3.Press y or z to highlight either TV or CABLE, depending on which you use. If you use an antenna, highlight TV; if you use cable channels, highlight CABLE.

LANGUAGE	SET UP
LANGUAGE	TV
CLOCK SET	CABLE
ANT 1 / 2
TV / CABLE
CH PROGRAM
ADD / ERASE
: SELECT	ENTER : SET

4.Press ENTER.

5.Press z to select CH PROGRAM.

	SET UP
LANGUAGE		ENGLISH

CLOCK SET		0 0 : 0 0
ANT 1 / 2		ANT1
TV / CABLE		CABLE
CH PROGRAM
ADD / ERASE		ADD

: MOVE ENTER : START

6.Press ENTER to start channel programming. The TV will automatically cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory.

While the TV is cycling through the channels, the message “Programming Now—Please Wait” appears.

7.When channel programming is complete, the message “Completed” appears.

8.Press Channel y or z to view the programmed channels.

POWER

TV

CABLE/SAT LIGHT SLEEP

VCR

DVD 1 2 3

AUDIO1

AUDIO2 4 5 6 MODE

			7			8	9
PIC SIZE			+10
			+10			0
ACTION			100/			0	ENT
MENU			O	FAV		ORI
		NF				ORI	T
		I				TE	T
							HE
E							LI	AT
E							LI		E
ID							N			R
U								K
G			LE	SUB	TIT
			LE	SUB
			TIT
	P					LE	A
	U						U
T			FAV				DI
SE			FAV				O
							O
			ENTER
			FAV
CH							VOL
			EXIT
DVD RTN			DVD CLEAR
DVD RTN
CH RTN			INPUT	RECALL			MUTE

SLOW/DIR SKIP/SEARCH

MENU

ENTER

yzx •

Channel yz

Usingthe	RemoteControl


Settingup	yourTV


UsingtheTV’s	Features


Appendix


Index

27

Image 27

Contents Index Dlptm Projection TelevisionDear Customer Lamp Unit ReplacementInstallation Important Safety InstructionsCare ServiceImportant notes about your DLP projection TV Important Safety Information Introduction Exploring your new TV Introduction Connecting YourTV ControlIntroduction Welcome to ToshibaConnecting your TV Connecting an antenna or cable TVConnecting your TV You will need Three coaxial cables Connecting a VCRConnecting a cable converter box UsingConnecting a cable converter box and VCR Connecting a DVD player or satellite receiver and a VCR From Antenna Stereo VCR From DTV Antenna Connecting a camcorder Connecting two VCRsConnecting an Hdmi or a DVI device to the Hdmi inputs One Hdmi cable type a connectorOne pair of standard analog audio cables Connecting an audio system Using the remote control Preparing the remote control for useInstalling the remote control batteries Remote Control functional key chart Using the Remote ControlCBL/SAT Audio VCR TV/VCR TV/SAT Searching and sampling the code of a device Device code setupAppendix Index Connecting YourTVUsingthe RemoteControl Setting up your TV Features IntroductionDevice code table VCR setup codesCD Player setup codes Learning about the remote control UsingtheTV’s Features Setting up your TVIntroduction Connecting YourTV Usingthe RemoteControl Settingup yourTVSelecting the antenna input Changing the on-screen display languageTo program channels automatically Introduction Connecting YourTVAdding channels to the TV’s memory Programming channels automaticallyEnter Changing channelsSelecting the Quick Restart Adding and erasing channels manuallyUsing the TV’s features Adjusting the channel settingsIntroduction Connecting YourTV Usingthe Control Press Enter to display the Favorite CH menu Using the TV’s FeaturesPress y or z to highlight Favorite CHClear UsingtheTV’s Features AppendixLabeling channels Press z or y to highlightNatural picture size Selecting the picture sizeSetting your Usingthe RemoteControlTo lower the picture, press z Press Enter to display the Scroll Adjustment modeScrolling the TheaterWide picture TheaterWide 2 and 3 only To raise the picture, press yPress y or z to select ON, and then press Enter Using the Auto Aspect featureUsingthe RemoteControl Settingup YourTV Press y or z to highlight Auto ASPECT, and then pressTo close the POP window Press Split again or Exit Using the POP double-window featureSwitching the main and POP pictures Switching the speaker audio main or POPUp TV Double-Window aspect ratio Using the programmed channel search functionAbout the auto favorite feature Using the favorite channel search functionIf you cannot remember your PIN code Using the Locks menuUsing the V-CHIP menu Entering the PIN codePress z or y to select an item Enable BlockingOFF To release your setting Unlock TV Rating Independent rating system for broadcastersMpaa Rating Mpaa Rating Independent rating system for moviesLocking channels Unlocking programs temporarilyRepeat steps 2 and 3 for other channels Press y or z to highlight Clear ALL, and then press Enter From the Locks menu, press y or z to highlight NEW PIN Code Locking the video inputsChanging the PIN code OFFAdjusting the picture Selecting the picture modeAdjusting the picture quality Selecting the color temperature Press x or to select the mode you preferSaving your new preferences Done Using the CableClear DNR featureResetting picture adjustments ResetCinema Mode Selecting the Lamp modeConnecting YourTV Control Selecting the cinema modeSelecting the video input source Using the closed caption feature Press y or z to highlight Caption or TEXT, and then pressTo view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timerTo display the time on-screen Press Recall Adjusting the sound Muting the soundSelecting stereo/SAP broadcasts Settingup YourTV UsingtheTV’s Features Appendix Index Using the WOW surround sound featureUsing Remote Adjusting the sound qualityEnjoying the Dolby Virtual sound feature Resetting your audio adjustments Using the StableSound featureTo turn off the StableSound feature Select OFF in above Select on in above Turning off the built-in speakersSelecting the Audio OUT sound To turn on the built-in speakersDisplaying on-screen information Understanding the auto power off featureUnderstanding the last mode memory feature Selecting the background of the menu displayAppendix Lamp unit replacement User-replaceable component When to replace the lamp unitU.S Temperature of the lamp immediately How to replace the lamp unitCleaning the lamp unit glass Replace the thumb screw and hand-tighten Lamp unit disposal LED indicationsVIDEO/AUDIO Input SpecificationsTroubleshooting Limited United States Warranty Limited Canada Warranty Audio OUT sound, selecting IndexPage Page Manufactured by