Toshiba 62HMX84, 52HMX84 owner manual Replace the thumb screw and hand-tighten

Page 63

How to replace the lamp unit (continued)

8. Reattach the lamp unit door, making sure to insert the hooks on the left side of the lamp unit door inside the opening in the TV cabinet.

Insert the hooks inside the TV cabinet opening.

Lamp unit door

9. Replace the thumb screw and hand-tighten.

Thumb screw (hand-tighten only)

Lamp unit door

NOTE : Make sure the lamp unit door is installed securely; otherwise, the TV may not turn on.

10. Plug in the power cord and turn on the TV. After the initial warmup period (which may take up to several seconds for full picture brightness), the TV should operate normally. If any of the following conditions exist, turn off the TV, unplug the power cord, and repeat steps 1–9 to ensure that the lamp unit and lamp unit door are installed correctly:

•No picture

•Dark picture

•TV will not turn on

If, after repeating steps 1–9, the problem still exists:

•In the U.S., call Customer Service at 1-800-631-3811.

•In Canada, locate the nearest Toshiba authorized service depot by directing your web browser to www.toshiba.ca; click “Home Entertainment,” and then click “Support.”

Introduction


Connecting	yourTV


Usingthe	RemoteControl


Settingup	yourTV


UsingtheTV’s	Features


Appendix


Index

63

Image 63

Contents Index Dlptm Projection TelevisionDear Customer Lamp Unit ReplacementInstallation Important Safety InstructionsCare ServiceImportant notes about your DLP projection TV Important Safety Information Introduction Exploring your new TV Introduction Connecting YourTV ControlIntroduction Welcome to ToshibaConnecting your TV Connecting an antenna or cable TVConnecting your TV You will need Three coaxial cables Connecting a VCRConnecting a cable converter box UsingConnecting a cable converter box and VCR Connecting a DVD player or satellite receiver and a VCR From Antenna Stereo VCR From DTV Antenna Connecting a camcorder Connecting two VCRsConnecting an Hdmi or a DVI device to the Hdmi inputs One Hdmi cable type a connectorOne pair of standard analog audio cables Connecting an audio system Using the remote control Preparing the remote control for useInstalling the remote control batteries Remote Control functional key chart Using the Remote ControlCBL/SAT Audio VCR TV/VCR TV/SAT Searching and sampling the code of a device Device code setupAppendix Index Connecting YourTVUsingthe RemoteControl Setting up your TV Features IntroductionDevice code table VCR setup codesCD Player setup codes Learning about the remote control UsingtheTV’s Features Setting up your TVIntroduction Connecting YourTV Usingthe RemoteControl Settingup yourTVSelecting the antenna input Changing the on-screen display languageTo program channels automatically Introduction Connecting YourTVAdding channels to the TV’s memory Programming channels automaticallyEnter Changing channelsSelecting the Quick Restart Adding and erasing channels manuallyUsing the TV’s features Adjusting the channel settingsIntroduction Connecting YourTV Usingthe Control Press Enter to display the Favorite CH menu Using the TV’s FeaturesPress y or z to highlight Favorite CHClear UsingtheTV’s Features AppendixLabeling channels Press z or y to highlightNatural picture size Selecting the picture sizeSetting your Usingthe RemoteControlTo lower the picture, press z Press Enter to display the Scroll Adjustment modeScrolling the TheaterWide picture TheaterWide 2 and 3 only To raise the picture, press yPress y or z to select ON, and then press Enter Using the Auto Aspect featureUsingthe RemoteControl Settingup YourTV Press y or z to highlight Auto ASPECT, and then pressTo close the POP window Press Split again or Exit Using the POP double-window featureSwitching the main and POP pictures Switching the speaker audio main or POPUp TV Double-Window aspect ratio Using the programmed channel search functionAbout the auto favorite feature Using the favorite channel search functionIf you cannot remember your PIN code Using the Locks menuUsing the V-CHIP menu Entering the PIN codePress z or y to select an item Enable BlockingOFF To release your setting Unlock TV Rating Independent rating system for broadcastersMpaa Rating Mpaa Rating Independent rating system for moviesLocking channels Unlocking programs temporarilyRepeat steps 2 and 3 for other channels Press y or z to highlight Clear ALL, and then press Enter From the Locks menu, press y or z to highlight NEW PIN Code Locking the video inputsChanging the PIN code OFFAdjusting the picture Selecting the picture modeAdjusting the picture quality Selecting the color temperature Press x or to select the mode you preferSaving your new preferences Done Using the CableClear DNR featureResetting picture adjustments ResetCinema Mode Selecting the Lamp modeConnecting YourTV Control Selecting the cinema modeSelecting the video input source Using the closed caption feature Press y or z to highlight Caption or TEXT, and then pressTo view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timerTo display the time on-screen Press Recall Adjusting the sound Muting the soundSelecting stereo/SAP broadcasts Settingup YourTV UsingtheTV’s Features Appendix Index Using the WOW surround sound featureUsing Remote Adjusting the sound qualityEnjoying the Dolby Virtual sound feature Resetting your audio adjustments Using the StableSound featureTo turn off the StableSound feature Select OFF in above Select on in above Turning off the built-in speakersSelecting the Audio OUT sound To turn on the built-in speakersDisplaying on-screen information Understanding the auto power off featureUnderstanding the last mode memory feature Selecting the background of the menu displayAppendix Lamp unit replacement User-replaceable component When to replace the lamp unitU.S Temperature of the lamp immediately How to replace the lamp unitCleaning the lamp unit glass Replace the thumb screw and hand-tighten Lamp unit disposal LED indicationsVIDEO/AUDIO Input SpecificationsTroubleshooting Limited United States Warranty Limited Canada Warranty Audio OUT sound, selecting IndexPage Page Manufactured by