Toshiba 52HMX84, 62HMX84 owner manual LED indications, Lamp unit disposal

Page 64

Lamp unit disposal

Place the used lamp unit in the empty box from the new lamp unit.

Keep the lamp unit out of reach of children and pets.

CAUTION: Always handle the lamp unit with care.

The lamp unit in this TV was designed for safe replacement by consumers; however, if the lamp unit is subjected to intentional or accidental abuse (such as excessive mechanical abuse or handling by children or pets), the unit may break, exposing sharp edges or pinch points.

Dispose of the used lamp unit by the approved method for your area.

NOTE : The lamp unit contains mercury. Disposal of mercury may be regulated due to environmental

considerations. For disposal or recycling information, contact your local authorities or the Electronics Industries Alliance (www.eiae.org).

LED indications

The green and red LED lights on the TV control touchpad (on the lower right corner of the TV screen) indicate the TV’s current status, as follows:

Green ON = Control touchpad being pressed.

Red ON = Power ON.

Green and/or Red blinking (see table below for condition and solution).

Control touchpad on TV front

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TV/VIDEO EXIT

CHANNEL

VOLUME

MENU

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Red indicator

Green indicator

 

 

LED Indication

Condition

Solution

 

1)

Green lights solid;

The lamp unit door is not

Turn the POWER OFF and unplug the power cord. Review

 

 

 

Red blinks at

seated properly.

“How to replace the lamp unit” on pages 61–63 to ensure

 

 

 

0.5-second intervals.

 

that the lamp unit door is installed securely. If the problem

 

 

 

 

 

persists, contact a Toshiba Authorized Service Center.

 

2)

Green blinks at

The lamp is not working

The TV automatically will try to restart itself eight times.

 

 

 

0.3-second intervals;

properly.

 

 

 

 

Red lights solid.

 

 

 

 

 

 

 

 

 

3)

Green and Red blink

The lamp is not working

Turn the POWER OFF and then ON again. If the problem

 

 

 

 

at 1-second intervals.

properly after the eighth

persists, replace the lamp unit (see pages 61–63). If the

Appendix

 

 

 

automatic restart (see item

problem still persists, contact a Toshiba Authorized Service

 

 

 

#2).

Center.

 

 

 

 

 

4)

Green is off;

For service personnel only.

Turn the POWER OFF and unplug the power cord. If the

 

 

 

Red blinks.

 

problem persists, contact a Toshiba Authorized Service

 

 

 

 

 

Center.

 

5)

Green and Red blink

An abnormal temperature

Do not block or cover the slots or openings in the TV

 

 

 

three times.

increase has occurred.

cabinet.

 

 

 

 

 

 

 

 

If the problem persists, contact a Toshiba Authorized

 

 

 

 

 

Service Center.

64

Image 64
Contents Dlptm Projection Television IndexLamp Unit Replacement Dear CustomerImportant Safety Instructions InstallationService CareImportant notes about your DLP projection TV Important Safety Information Introduction Introduction Connecting YourTV Control IntroductionWelcome to Toshiba Exploring your new TVConnecting an antenna or cable TV Connecting your TVConnecting your TV Connecting a VCR Connecting a cable converter boxUsing You will need Three coaxial cablesConnecting a cable converter box and VCR Connecting a DVD player or satellite receiver and a VCR From Antenna Stereo VCR From DTV Antenna Connecting two VCRs Connecting a camcorderOne Hdmi cable type a connector Connecting an Hdmi or a DVI device to the Hdmi inputsOne pair of standard analog audio cables Connecting an audio system Preparing the remote control for use Using the remote controlInstalling the remote control batteries Using the Remote Control Remote Control functional key chartCBL/SAT Audio VCR TV/VCR TV/SAT Device code setup Searching and sampling the code of a deviceConnecting YourTV Usingthe RemoteControl Setting up your TV FeaturesIntroduction Appendix IndexVCR setup codes Device code tableCD Player setup codes Learning about the remote control Setting up your TV Introduction Connecting YourTV Usingthe RemoteControlSettingup yourTV UsingtheTV’s FeaturesChanging the on-screen display language Selecting the antenna inputIntroduction Connecting YourTV Adding channels to the TV’s memoryProgramming channels automatically To program channels automaticallyChanging channels Selecting the Quick RestartAdding and erasing channels manually EnterAdjusting the channel settings Using the TV’s featuresIntroduction Connecting YourTV Usingthe Control Using the TV’s Features Press y or z to highlightFavorite CH Press Enter to display the Favorite CH menuUsingtheTV’s Features Appendix Labeling channelsPress z or y to highlight ClearSelecting the picture size Natural picture sizeUsingthe RemoteControl Setting yourPress Enter to display the Scroll Adjustment mode Scrolling the TheaterWide picture TheaterWide 2 and 3 onlyTo raise the picture, press y To lower the picture, press zUsing the Auto Aspect feature Usingthe RemoteControl Settingup YourTVPress y or z to highlight Auto ASPECT, and then press Press y or z to select ON, and then press EnterUsing the POP double-window feature To close the POP window Press Split again or ExitSwitching the speaker audio main or POP Switching the main and POP picturesUp TV Using the programmed channel search function Double-Window aspect ratioUsing the favorite channel search function About the auto favorite featureUsing the Locks menu Using the V-CHIP menuEntering the PIN code If you cannot remember your PIN codeEnable Blocking OFF To release your setting UnlockTV Rating Independent rating system for broadcasters Press z or y to select an itemMpaa Rating Independent rating system for movies Mpaa RatingUnlocking programs temporarily Locking channelsRepeat steps 2 and 3 for other channels Press y or z to highlight Clear ALL, and then press Enter Locking the video inputs Changing the PIN codeOFF From the Locks menu, press y or z to highlight NEW PIN CodeSelecting the picture mode Adjusting the pictureAdjusting the picture quality Press x or to select the mode you prefer Selecting the color temperatureSaving your new preferences Using the CableClear DNR feature Resetting picture adjustmentsReset DoneSelecting the Lamp mode Connecting YourTV ControlSelecting the cinema mode Cinema ModeSelecting the video input source Press y or z to highlight Caption or TEXT, and then press Using the closed caption featureTo view text, highlight T1, T2, T3, or T4 Setting the on timer Setting the sleep timerTo display the time on-screen Press Recall Muting the sound Adjusting the soundSelecting stereo/SAP broadcasts Using the WOW surround sound feature Using RemoteAdjusting the sound quality Settingup YourTV UsingtheTV’s Features Appendix IndexEnjoying the Dolby Virtual sound feature Using the StableSound feature Resetting your audio adjustmentsTo turn off the StableSound feature Select OFF in above Turning off the built-in speakers Selecting the Audio OUT soundTo turn on the built-in speakers Select on in aboveUnderstanding the auto power off feature Understanding the last mode memory featureSelecting the background of the menu display Displaying on-screen informationWhen to replace the lamp unit Appendix Lamp unit replacement User-replaceable componentU.S How to replace the lamp unit Temperature of the lamp immediatelyCleaning the lamp unit glass Replace the thumb screw and hand-tighten LED indications Lamp unit disposalSpecifications VIDEO/AUDIO InputTroubleshooting Limited United States Warranty Limited Canada Warranty Index Audio OUT sound, selectingPage Page Manufactured by