Toshiba 62HMX84, 52HMX84 How to replace the lamp unit, Temperature of the lamp immediately

Page 61

How to replace the lamp unit

Required tool: Manual Phillips screwdriver; gloves.

Optional tool: 5/32” or 4mm Allen wrench.

1. Turn off the TV and unplug the power cord.

WARNING: Eye damage may result from

directly viewing the light produced by this lamp. Always turn off the TV and unplug the power cord before opening the lamp unit door.

2. STOP! Allow the lamp to cool for at least one (1) hour before replacing it.

CAUTION: HOT SURFACE

The temperature of the lamp immediately

after use exceeds 392ûF (200ûC). Touching the lamp before it has cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE REPLACING IT.

3. On the lamp unit door on the side of the TV, loosen the thumb screw by hand or by using a 5/32” or 4mm Allen wrench, and then remove the lamp unit door.

TV back

Thumb screw

Lamp unit door detail

WARNING: RISK OF

ELECTRIC SHOCK! The lamp

unit door is provided with an interlock to reduce the risk of electric shock and excessive ultraviolet radiation. Never defeat its purpose or attempt to service without removing the lamp unit door completely. Failure to follow this WARNING may result in death or serious injury.

4. Using a manual Phillips screwdriver, loosen the two screws on the lamp unit.

Lamp unit screws

WARNING: RISK OF

ELECTRIC SHOCK!

TO REDUCE THE RISK OF ELECTRIC SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS SPECIFIED HEREIN. REFER ALL SERVICING NOT SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE PERSONNEL. Failure to follow this WARNING may result in death or serious injury.

Introduction

 

 

 

 

 

Connecting

yourTV

 

 

 

 

Usingthe

RemoteControl

 

 

 

 

Settingup

yourTV

 

 

 

 

UsingtheTV’s

Features

 

 

 

 

Appendix

 

 

 

 

 

Index

 

 

 

(Continued on next page)

61

Image 61
Contents Index Dlptm Projection TelevisionDear Customer Lamp Unit ReplacementInstallation Important Safety InstructionsCare ServiceImportant notes about your DLP projection TV Important Safety Information Introduction Introduction Introduction Connecting YourTV ControlWelcome to Toshiba Exploring your new TVConnecting an antenna or cable TV Connecting your TVConnecting your TV Connecting a cable converter box Connecting a VCRUsing You will need Three coaxial cablesConnecting a cable converter box and VCR Connecting a DVD player or satellite receiver and a VCR From Antenna Stereo VCR From DTV Antenna Connecting a camcorder Connecting two VCRsOne Hdmi cable type a connector Connecting an Hdmi or a DVI device to the Hdmi inputsOne pair of standard analog audio cables Connecting an audio system Preparing the remote control for use Using the remote controlInstalling the remote control batteries Remote Control functional key chart Using the Remote ControlCBL/SAT Audio VCR TV/VCR TV/SAT Searching and sampling the code of a device Device code setupUsingthe RemoteControl Setting up your TV Features Connecting YourTVIntroduction Appendix IndexDevice code table VCR setup codesCD Player setup codes Learning about the remote control Introduction Connecting YourTV Usingthe RemoteControl Setting up your TVSettingup yourTV UsingtheTV’s FeaturesSelecting the antenna input Changing the on-screen display languageAdding channels to the TV’s memory Introduction Connecting YourTVProgramming channels automatically To program channels automaticallySelecting the Quick Restart Changing channelsAdding and erasing channels manually EnterAdjusting the channel settings Using the TV’s featuresIntroduction Connecting YourTV Usingthe Control Press y or z to highlight Using the TV’s FeaturesFavorite CH Press Enter to display the Favorite CH menuLabeling channels UsingtheTV’s Features AppendixPress z or y to highlight ClearNatural picture size Selecting the picture sizeSetting your Usingthe RemoteControlScrolling the TheaterWide picture TheaterWide 2 and 3 only Press Enter to display the Scroll Adjustment modeTo raise the picture, press y To lower the picture, press zUsingthe RemoteControl Settingup YourTV Using the Auto Aspect featurePress y or z to highlight Auto ASPECT, and then press Press y or z to select ON, and then press EnterTo close the POP window Press Split again or Exit Using the POP double-window featureSwitching the speaker audio main or POP Switching the main and POP picturesUp TV Double-Window aspect ratio Using the programmed channel search functionAbout the auto favorite feature Using the favorite channel search functionUsing the V-CHIP menu Using the Locks menuEntering the PIN code If you cannot remember your PIN codeOFF To release your setting Unlock Enable BlockingTV Rating Independent rating system for broadcasters Press z or y to select an itemMpaa Rating Mpaa Rating Independent rating system for moviesUnlocking programs temporarily Locking channelsRepeat steps 2 and 3 for other channels Press y or z to highlight Clear ALL, and then press Enter Changing the PIN code Locking the video inputsOFF From the Locks menu, press y or z to highlight NEW PIN CodeSelecting the picture mode Adjusting the pictureAdjusting the picture quality Press x or to select the mode you prefer Selecting the color temperatureSaving your new preferences Resetting picture adjustments Using the CableClear DNR featureReset DoneConnecting YourTV Control Selecting the Lamp modeSelecting the cinema mode Cinema ModeSelecting the video input source Press y or z to highlight Caption or TEXT, and then press Using the closed caption featureTo view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timerTo display the time on-screen Press Recall Muting the sound Adjusting the soundSelecting stereo/SAP broadcasts Using Remote Using the WOW surround sound featureAdjusting the sound quality Settingup YourTV UsingtheTV’s Features Appendix IndexEnjoying the Dolby Virtual sound feature Using the StableSound feature Resetting your audio adjustmentsTo turn off the StableSound feature Select OFF in above Selecting the Audio OUT sound Turning off the built-in speakersTo turn on the built-in speakers Select on in aboveUnderstanding the last mode memory feature Understanding the auto power off featureSelecting the background of the menu display Displaying on-screen informationWhen to replace the lamp unit Appendix Lamp unit replacement User-replaceable componentU.S Temperature of the lamp immediately How to replace the lamp unitCleaning the lamp unit glass Replace the thumb screw and hand-tighten Lamp unit disposal LED indicationsVIDEO/AUDIO Input SpecificationsTroubleshooting Limited United States Warranty Limited Canada Warranty Audio OUT sound, selecting IndexPage Page Manufactured by