Sherwood VR-654BD manual Troubleshooting Guide, REmOTE Control Unit PROBLEm, REmEDY

Page 50

VR-654(G)_ENG_100129_VR-654(G) 2010-01-29 오전 10:45 페이지 50

Troubleshooting Guide

ENGLISH

If a fault occurs, run through the table below before taking your receiver for repair.

If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you attempt to repair the unit yourself. This could void the warranty.

■REmOTE CONTROL UNIT

PROBLEm

POSSIBLE CAUSE

REmEDY

 

 

 

No operation

• Batteries are not loaded or exhausted.

• Replace the batteries.

• The remote sensor is obstructed.

• Remove the obstacle.

 

 

 

 

■mAIN UNIT

 

 

[AmPLIFIER SECTION]

 

 

 

 

 

PROBLEm

POSSIBLE CAUSE

REmEDY

 

 

 

No power

• The AC input cord is disconnected.

• Connect cord securely.

 

• Poor connection at AC wall outlet or the outlet is

• Check the outlet using a lamp or another appliance.

 

inactive.

 

 

 

 

No sound

• The speaker cords are disconnected.

• Check the speaker connections.

 

• The master volume is adjusted too low.

• Adjust the master volume.

 

• The MUTE button on the remote control is

• Press the MUTE button to cancel the muting effect.

 

pressed to ON.

 

 

• Incorrect selection of input source.

• Select the desired input source correctly.

 

• Incorrect connections between the components.

• Make connections correctly.

 

 

 

Noise or distorted sound

• Poor connections.

• Check the connections and connect all cords

 

 

securely.

 

 

 

No sound from the surround

• Surround mode is switched off(stereo mode).

• Select a surround mode.

speakers

• Master volume and surround level are too low.

• Adjust master volume and surround level.

 

• Monaural source is used.

• Select a stereo or surround source.

 

• Surround speaker setting is "NO".

• Select the desired surround speaker setting.

 

 

 

No sound from the center

• Stereo mode, etc is selected.

• Select the desired surround mode.

speaker

• Center speaker setting is "NO".

• Select the desired center speaker setting.

 

• Master volume and center level are too low.

• Adjust master volume and center level.

 

 

 

No sound from the surround

• The input signal format or the current surround

• Under the proper situations, perform the 7.1(or 6.1)

back speakers

mode cannot support the 7.1(or 6.1) surround.

surround playback.(For details, refer to "ENJOYING

 

 

SURROUND SOUND" on page 17.)

 

• Master volume and surround back level are too

• Adjust master volume and surround back level.

 

low.

 

 

• Surround back speaker setting is "NO".

• Select the desired surround back speaker setting.

 

 

 

[TUNER SECTION]

 

 

 

 

 

PROBLEm

POSSIBLE CAUSE

REmEDY

 

 

 

Station cannot be received

• No antenna is connected.

• Connect an antenna.

 

• The desired station frequency is not tuned in.

• Tune in the desired station frequency.

 

• The antenna is in wrong position.

• Move the antenna and retry tuning.

 

 

 

Preset stations cannot be

• An incorrect station frequency has been

• Memorize the correct station frequency.

received

memorized.

 

 

• The memorized stations are cleared.

• Memorize the stations again.

 

 

 

Poor FM reception

• No antenna is connected.

• Connect an antenna.

 

• The antenna is not positioned for the best

• Change the position of the antenna.

 

reception.

 

 

 

 

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents VR-654BD Introduction PAN-EUROPEAN Unified VoltageLeave a space around the unit for sufficient ventilation Moisture condensationContents Connecting AUDIO/VIDEO COmPONENTS System ConnectionsHdmi OUT Video output resolutionCopyright protection system Connecting speaker wire Connecting Digital INsConnecting SPEAkERS Connecting PREOUTs Speaker placementConnecting for SYSTEm Control Connecting to NETWORkOPEN/CLOSE Front Panel ControlsRemote Sensor Fluorescent Display PLAY/PAUSEUniversal Remote Controls Enter a 3 digit code EnteRInG a setUP coDeFunction Table of the Numbered Buttons Repeat the above steps 1 to 4 for each of your componentsReMote contRoL oPeRAtIon RAnGe LoADInG BAtteRIesListening to a PROGRAm Source When SAT, TV, AUx is selected as an input sourceBasic Operation Operating the sleep timer Adjusting the brightness of the fluorescent displaySURRoUnD soUnD Surround modesMovie When selecting an input source other than BD/DVDWhen selecting the BD/DVD DramaTurn the setup menu on SYSTEm SetupSetting the sound parameter Select the desired menu using the Cursor UP/DOWN buttonsWhen selecting the DRC Dynamic Range Control When selecting the L.SYNC Lip-SyncWhen selecting the D.m. Dual mono When selecting the LFE LFE levelSetting the speaker setup When selecting the SPEAkER Configuration About the speaker sizeWhen selecting the Channel Level To cancel the test tone function, press the Return buttonWhen selecting the Crossover Frequency Press the OK button to confirm your selectionWhen selecting the SPEAkER Distance Setting the Tone①. Press the OK button to enter the tone adjustment mode About the speaker distanceUnplayable discs PReLIMInARY KnoWLeDGe ABoUt DIscs Playable disc typesRegion code Color system formatCARe AnD HAnDLInG oF DIscs SYMBoL ABoUt InVALID oPeRAtIonPLAYABLe FILes DeFInItIon oF teRMs Avchd Advanced Video Codec High DefinitionJpeg Joint Photographic Experts Group To start playback from the menu Case of use of the NUmERIC buttons on the remote controlPLAYInG a DIsc Before starting playbackSlow playback To stop playbackTo pause playback Frame advance playbackDuring playback, press the GO to button Displaying disc informationPlaying the desired section of disc Press the OK buttonPlaying a specific section repeatedly Operations using disc menu, top menu, and Pop-up menuPlaying repeatedly Playing in random orderDuring playback, press the Audio button Switching the audio soundtrackDuring playback, press the Popup Menu button Press the Popup button to exitDuring playback, press the Subtitle button Switching the subtitlesSwitching the camera angles Virtual Package Press the Cursor Right button to enter the PIP mode menuPlaying secondary videoPicture in Picture When selecting the Add To Playlist When selecting the Playlist Optical Disc or the USBWhen selecting the Remove from Playlist When selecting the Play FileSelecting an item in the play menu To specify the time intervalPlaying the desired section of file When entering file numberDisplaying file information When selecting the Slide Show Delay When clearing the number enteredWhen selecting the Slide Show Effects To change the effect on displaying picturesDuring playback of music files, press the OK button To control the music filesOSD Menu Settings SettInG tHe sYsteM SettInG tHe DIsPLAY SettInG tHe AUDIo SettInG tHe LAnGUAGeWhen selecting the Parental Password SettInG tHe PARentAL contRoLWhen selecting the Parental Control or the Parental Level Parental Password CancelIP Settings SettInG tHe netWoRKWhen selecting the Wired When selecting the manualWhen selecting the Off When selecting the Network TestWhen selecting the manual or the Dynamic Auto presetting Auto tuningManual tuning Select the desired FM modeTuning Presetting radio stationsTuning to preset stations MEmORY BACkUP FunctionSearching for stations by program type FM mode, press the Search Mode buttonListening to RDS BROADCASTSFm only Displaying RDS informationMAIN Unit AmPLIFIER Section PROBLEm Troubleshooting GuideREmOTE Control Unit PROBLEm REmEDYBD Player Section Specifications 70 / 65 dB Fm Tuner SectionDBf Setup Code Table Interfunk Inno HITNordmende OceanicSamsung SambersSampo SanyoCH.MASTER ArconAstra City COMGNU General Public License PreambleEnglish No Warranty How to Apply These Terms to Your New Programs VR-654BD
Top Page Image Contents