Universal Electronics ATLAS OCAP 5-Device manual Programming a Learned Key

Page 15

Learning capacity is approximately 16 to 25 keys, depending on the code being learned.

Certain device functions are not learnable including multi-frequency types, some high frequency ones, and other unusual formats.

For optimum learning, avoid high levels of ambient light such as natural sunlight or energy-efficient fluorescent lights.

NOTE: Please have your original remote controls handy before programming learning.

Programming a Learned Key

NOTE: If more than 15 seconds pass between key presses, the remote exits programming.

1.Press and hold SETUP until the last-selected

mode key blinks twice, then press 9 7 5.

NOTE: If the LED displays one long flash instead, either your batteries are low, or the Atlas OCAP 5-Device Remote Control with Learn- ing has a memory fault.

2.Press a mode key once (i.e., VCR, DVD, AUD,

TV, or CBL) to assign a mode for learning.

3.Then press the key on your Atlas OCAP Remote Control that learns the new code.

4.Place the Atlas OCAP 5-Device Remote Control with Learning head-to-head (about 2" apart) from your original remote control. Also locate the key (on your original remote control) that you want the Atlas OCAP 5- Device Remote Control with Learning to learn.

2"

5.On the original remote, press and hold the key to be learned. The Atlas OCAP 5-Device Remote Control with Learning’s LED will blink rapidly, then turn off. Continue holding

www.urcsupport.com/atlasocap

15

Image 15
Contents Preprogrammed for Your SET-TOP BOX Table of Contents Page Introduction Features and Functions KeyFunction Key ChartsUse VOL+ or VOL- to raise or lower the audio volume Device Key Device TableInstalling Batteries Programming Device Control Aim the remote control at the deviceSetting UP a Combo Unit Searching for Your Code Aim the remote control at your combo devicePage Using Learning Learning PrecautionsChecking the Codes Programming a Learned Key TV, or CBL Deleting a Single Learning KeyUnlocking Channel Control Programming Channel Control LockLocking Channel Control to CBL Changing Volume LockLocking Volume Control To One Mode Global Volume Lock Programming Macro Keys Programming Cable ID LockClearing a Macro Key Programming a Macro KeyProgramming the Master Power Key Using the Master Power KEYUsing the Master Power Key Clearing the Master Power KeyRE-ASSIGNING Device Keys VCR Setup 9 9 2 VCR VCR VCR Setup 9 9 2 AUD VCRVCR Setup 9 9 2 TV VCR VCR Setup 9 9 2 CBL VCRActivating Backlighting Optional TroubleshootingFCC Notice Additional Information Setup Codes for Audio Amplifiers Setup Codes for Audio ReceiversMANUFACTURER’S Codes AMW MCS JBLKLH LXI1023, 1609, 1254 ABC Setup Codes for Audio AccessoriesSetup Codes for Cable Boxes/Converters SSI1256 Setup Codes for DVD Players Setup Codes for Cable/DVR/PVR CombosBBK CavsESA JSI GPX0591, 0692 SVA Page Setup Codes for DVD Combos LCD Setup Codes for DVD RecordersHTS GOIABS UsdtvSetup Codes for DVR/PVR Systems CCE AOCCXC Page KTV JCBKEC KMCNTC MTC1447, 0047, 1958 SSS TVS TMKSetup Codes for TVs Hdtv 0047 Setup Codes for TVs Plasma Setup Codes for TV/DVD Combos Hitachi 1247 ILo 1472 Initial Jensen 1016 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos Setup Codes for VCRs HI-Q Keen 0693 Kenwood 0067, 0041, 0038 0060, 0240, 0042 STS Setup Codes for Video Accessories DDIDvico SMC Setup Codes for Video Accessories HdtvPage Page M1056L Revision