Universal Electronics ATLAS OCAP 5-Device manual Programming Device Control

Page 10

PROGRAMMING DEVICE CONTROL

The Atlas OCAP 5-Device Remote Control with Learning is preprogrammed to operate the cable box (converter) provided by your cable system, an RCA TV, a Toshiba DVD player, an RCA VCR, and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps; otherwise skip this section.

NOTES: For control of a Combo device (for example, a TV/VCR combo), skip this section and per- form the instructions on “Setting Up a Combo Unit” on page 11. Also refer to “Device Table” on page 8 to find out which devices can be programmed onto each device key.

If you have another brand of cable converter or a satellite receiver you would like to control, you’ll need to unlock the cable ID Lock before changing the converter code (see “Program- ming Cable ID Lock” on page 20).

1.Turn on a device and, if applicable, insert video media, (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.

2.On the remote control, press a device key once

(i.e., VCR, DVD, AUD, TV, or CBL); it will blink once. Then press and hold SETUP until the selected mode key blinks twice.

3.Use the “Manufacturer’s Codes” starting on page 28) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the selected mode key will blink twice.

NOTE: If the selected mode key emits a long blink, the entry is invalid. Repeat steps 2 through 3 and try entering the same code again.

4.Aim the remote control at the device and

press PWR once. The device should turn off. If it does not, repeat steps 2 through 3, trying each code for your brand until you find one that works. If it still does not respond, try searching for the code (see “Searching for Your Code” on page 13).

NOTE: If the device does not have a PWR key, press the ￿(Play) key.

www.urcsupport.com/atlasocap

10

Image 10
Contents Preprogrammed for Your SET-TOP BOX Table of Contents Page Introduction Features and Functions Key Charts KeyFunctionUse VOL+ or VOL- to raise or lower the audio volume Device Table Device KeyInstalling Batteries Aim the remote control at the device Programming Device ControlSetting UP a Combo Unit Aim the remote control at your combo device Searching for Your CodePage Learning Precautions Using LearningChecking the Codes Programming a Learned Key Deleting a Single Learning Key TV, or CBLProgramming Channel Control Lock Unlocking Channel ControlChanging Volume Lock Locking Channel Control to CBLLocking Volume Control To One Mode Global Volume Lock Programming Cable ID Lock Programming Macro KeysProgramming a Macro Key Clearing a Macro KeyUsing the Master Power KEY Programming the Master Power KeyClearing the Master Power Key Using the Master Power KeyRE-ASSIGNING Device Keys VCR Setup 9 9 2 CBL VCR VCR Setup 9 9 2 AUD VCRVCR Setup 9 9 2 TV VCR VCR Setup 9 9 2 VCR VCRTroubleshooting Activating Backlighting OptionalFCC Notice Additional Information Setup Codes for Audio Receivers Setup Codes for Audio AmplifiersMANUFACTURER’S Codes AMW LXI JBLKLH MCS1023, 1609, 1254 SSI Setup Codes for Audio AccessoriesSetup Codes for Cable Boxes/Converters ABC1256 Setup Codes for Cable/DVR/PVR Combos Setup Codes for DVD PlayersCavs BBKESA GPX JSI0591, 0692 SVA Page Setup Codes for DVD Recorders Setup Codes for DVD Combos LCDGOI HTSUsdtv ABSSetup Codes for DVR/PVR Systems AOC CCECXC Page KMC JCBKEC KTVMTC NTC1447, 0047, 1958 SSS TMK TVSSetup Codes for TVs Hdtv 0047 Setup Codes for TVs Plasma Setup Codes for TV/DVD Combos Hitachi 1247 ILo 1472 Initial Jensen 1016 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos Setup Codes for VCRs HI-Q Keen 0693 Kenwood 0067, 0041, 0038 0060, 0240, 0042 STS DDI Setup Codes for Video AccessoriesDvico Setup Codes for Video Accessories Hdtv SMCPage Page M1056L Revision