Mitsubishi Electronics WD-52725, WD-62525 manual 100

Page 100

Troubleshooting, continued

 

Problem

 

Possible Solution

 

 

42.

The IEEE 1394 device cannot be selected.

• The device may be busy, either recording or a peer-to-peer

 

 

 

connection has been established. Cancel the recording or

 

 

 

peer-to-peer connection.

 

 

 

43.

DEVICE MENU button does not display a menu.

• The IEEE 1394 device does not provide a menu.

 

 

• The TV cannot support IEEE 1394 menus. See page 46.

 

 

 

44.

All IEEE 1394 devices disappear.

• The connected devices must not be in a loop that returns to the

 

 

 

TV. Make sure a device is connected at the end.

 

 

• Disconnect all the cables and devices from the TV. Replace them one

 

 

 

by one to locate the problem device or cable.

 

 

• Use System Reset (front control panel).

 

 

 

45.

Cannot rediscover a deleted IEEE 1394 device

• The device has been disconnected. Plug it in.

 

 

• The device is unchecked in the Review screen. Select NetCommand

 

 

 

from the Main menu, then select Review. Check the device.

 

 

• Remove IEEE 1394 plug. Go to the Edit NetCommand menu. Delete

 

 

 

the IEEE 1394 device. Plug the device in again so it can be

 

 

 

discovered again.

 

 

 

46.

An IEEE 1394 device has been plugged in but

• The IEEE 1394 connection to the TV or another device is not secure

 

does not appear in the Device Selection menu

 

or is loose.

 

(not discovered).

• The IEEE 1394 device is not powered on.

 

 

• A device in the IEEE 1394 chain is not powered on - turn on all the

 

 

 

devices.

 

 

• The device discovery can take as long as a minute to initiate.

 

 

• IEEE 1394 cable is too long (maximum of 15 feet between devices).

 

 

• The IEEE 1394 device uses an incompatible protocol and will not be

 

 

 

discovered

 

 

 

47.

Cannot record to or from the IEEE 1394 device,

• To initiate a recording to IEEE 1394 device press the REC key.

 

including Dub recordings.

 

The Record menu displays allowing setup of the recording.

 

 

• The source device for the recording is not powered on.

 

 

• When dubbing, the destination device for the recording

 

 

 

is not powered on.

 

 

• The wrong media, (analog tape for digital recording, or

 

 

 

digital tape for the analog recording) is in the device.

 

 

• Either the program is copy protected, or if there are multiple

 

 

 

subchannels and one of the programs (not necessarily the

 

 

 

program requested) is copy protected.

 

 

• The program has already been recorded once and the copy

 

 

 

protection only allows one recording.

 

 

• Unapproved source device for copy protected material.

 

 

• The recording device can not decode the copyright signal

 

 

 

included in the signal source (try another device if available).

 

 

• The playing device (for dubbing) does not support

 

 

 

copyrighted material.

 

 

• Source for recording is copyrighted.

 

 

• Too many IEEE 1394 devices in network. Insufficient

 

 

 

bandwith available. Disconnect unused devices.

 

 

• Source Device has higher speed (S 400) than record device. If

 

 

 

possible, reverse devices, play in the slower device and record

 

 

 

in the faster device.

 

 

 

48.

Cannot control the IEEE 1394 device from the

• Device may not support the command.

 

Transport Menu.

• Selected function is gray (such as Record for a DVD, which does not

 

 

 

support the Record function).

 

 

 

 

49.

When ChannelView™ list is displayed,

•

Available information is sent from the broadcaster or cable provider.

 

information appears incomplete

 

No other data is available.

 

 

 

 

50.

Program to be recorded was correctly selected

•

The broadcaster supplied program information that was incorrect

 

from ChannelView, however, incorrect program

 

and/or was changed after a recording was added to the Record List.

 

was recorded.

 

 

 

 

 

 

51.

Incomplete ChannelView program recorded.

•

Recording device may have lack of space availability and there is not

 

 

 

enough blank space to make a full recording.

 

 

 

 

100

Page 99 Page 101
Image 100
Page 99 Page 101
Contents Owner’s Guide Stand Requirement FCC Declaration of Conformity Contents Special Features Ieee 1394 Devices and NetCommand Controlled RecordingsTV Menu Screen Operations Important Safeguards Important Safeguards Our Thanks Mitsubishi Digital Electronics America, IncTelevision Overview TV Accessories Special Features Front Control PanelBack Panel TV Accessories Special FeaturesSystem Reset IndicatorsReset Front Control PanelMedia Card Slots and Ieee 1394 Input/Output Front Panel Inputs and Media Card SlotsInput Back Panel Component-1, -2 InputsCableCARD Slot Input-1, -2 Monitor OutputIR Emitter-NetCommand PC Input and AudioDTV Link/IEEE1394 DVI Analog AudioConnecting Connecting External Devices & NetCommand Setup ChartConnecting a Wall Outlet Cable or Cable Box Wall Outlet CableUsing a CableCARD CableCARD TechnologyConnecting a Lead Antenna or Separate UHF and VHF Antenna Separate UHF and VHF AntennaFor antennas with twin flat lead For cable or antenna with coaxial leadConnecting a VCR to an Antenna or Wall Outlet Cable Connecting VCR Video and Audio to a Cable Box Cable Box Back panelConnecting an A/V receiver Connecting a DVD Player with Component DTV Connectors and Adaptors DTV Receiver with Component VideoDTV Receiver with RGB, HV Video Connecting a DTV Receiver with RGB, HV VideoDTV Receiver to TV Back Panel Link Control RS-232C Connection LinkConnecting the IR Emitter NetCommand Quadruple IR Emitter cable is included with the TVConnecting Compatible Ieee 1394 Devices When Connecting Ieee 1394 DevicesDigital Video Signals Digital Audio SignalsPin Style vs -Pin Style Connectors Connection StylesDirect Device-To-Device Style Hub Connection StyleConnecting Helpful Hints NetCommand Setup and Editing Using the Remote Control with NetCommand NetCommand Pre-Memorized DevicesRemote Control Functions Overview OverviewRemote Control FunctionsOperation and Care, Sleep Timer For Best Results from the Remote ControlInstalling the Batteries Setting the Sleep TimerNetCommand Setup On Screen Buttons Remote Control Buttons 3D Graphical Menu SystemNetCommand Initial Setup NetCommand Information ScreenDevice Setup Screen Welcome ScreenReview Screen Review screenReceiver Screen Edit NetCommand, Add an A/V ReceiverReceiver Inputs Receiver Input Learn Screen Receiver Learn ScreenName Screen Monitor Out to AVR ScreenEdit NetCommand Screen Edit NetCommand, Add DevicesAdd Screen Device Screen Edit NetCommand Add DevicesDevice Learn Screen Device Advanced Learn Screen Connection for Device ScreenVCR for Recordings Screen RF Connection for Cable ScreenInput-DTV Connection Screen IR Code for Device ScreenChange Device Screen Edit NetCommand, Change or Delete Devices, Finish ScreenDelete Device Screen Ieee 1394 Devices NetCommand Controlled Recordings NetCommand Controlled RecordingsDevice Selection Menu Disc Search Track List Screen PC ViewingIeee 1394 Devices and NetCommand Control Adding Ieee 1394 Devices Automatically Adding Ieee 1394 Devices AutomaticallyNew 1394 Device Screen Name for 1394 Device ScreenIeee 1394 Device Type Screen Connection ScreenDevice Selection Menu Power On/Off DevicesPIP Device Selection Menu Using the Device Menu Button to Display Menus Device MenuIR Controlled Devices CableCARD MenuUsing the Guide Button to Display ChannelView and Menus Guide ButtonDevices 1394 or IR Controlled ChannelViewTime-Delayed Recording Record To SetupRecording Now Cancel Current Recordings Record List ScreenCopy-Protected Material Restrictions for Traditional VCRsNetCommand Controlled Peer-to-Peer Connections What is a Peer-to-Peer Connection?Setting up a Peer-to-Peer Connection Canceling a Current Peer-to-Peer ConnectionDirect VCR Recording from an Antenna or Cable Source Disc SearchPC Viewing PC InputMediaCommand and Media Card Playback Media Card SlotsInserting a media card Don’t pull the media card out while it is playingMedia Command and Media Card Playback TV Menu Screen Operations Main menu, Setup selected Main Menu ChoicesSetup Menu NetCommand Menu Antenna Menu MemorizePrefer Digital ChannelAntenna Menu, SuperQuickView SQV SQV SuperQuickViewTime Menu Captions Menu Analog and Digital Captions Captions Menu, Customizing Digital Settings Chip Lock Menu Passcode ChipEntry Chip Start Time and V-Chip Stop TimeChip Signal Information Content CategoriesChip Lock Menu V-Chip Definitions TV RatingsLock By Time Chip Lock MenuFront Button Lock AudioVideo Menu Setting Descriptions Audio Analog and Digital Audio SettingAnalog Only Audio Settings Digital Only Audio SettingsVideo Settings Setting Descriptions VideoFor a Currently Viewed PC Operation of PIP and POP Warranty IndexDisplay Formats Signals and Formats DefinitionsDVD Definitions Original Signal TV Display FormatsPC Display Formats Device Control with Net Command NetCommand Compatible Traditional Devices AnalogWhen an Ieee 1394 Device is Viewed or Played Ieee 1394 DevicesBypassing the V-Chip Lock Appendix a Bypassing the V-Chip LockBypassing Front Button Lock This page intentionally blank TV Specifications Appendix B SpecificationsInputs Outputs Appendix CRemote Control Programming Codes Programming the Remote to Control NetCommand A/V ProductsAppendix C Remote Control Programming Codes DVD PlayersCable Boxes and Satellite Receivers ReceiversMitsubishi A/V Receivers Mitsubishi CD Players Not all functions for all modelsAppendix D On Screen Information Displays Appendix E NetCommand Specialized Device Keys Screen Remote Checkbox NameAppendix F Cleaning and Service To Install the Diamond Shield Appendix G Diamond Shield RemovalTo Remove the Diamond Shield For further assistance, call 800Appendix H Filter Cleaning Replace the lamp cartridgeAppendix H Lamp Cartridge Replacement Lamp LifeReplacing the Lamp Cartridge Troubleshooting Problem Possible SolutionTroubleshooting Troubleshooting 100 Using The System Reset Button 101Additional Information 102Index 103104 Icon Order, Viewing, Changing 64 IEEE1394Mitsubishi TV Software 105Mitsubishi DLP Projection Television Limited Warranty 106This Warranty does not Cover 107MDEAservice@mdea.com Website
Top Page Image Contents