Mitsubishi Electronics WD-52725, WD-62525 manual Stand Requirement

Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This TV is very heavy! Exercise extreme care when lifting or moving. A minimum of two adults should lift or move the TV.

Portions of the advanced circuitry of this TV must continue to operate even when the TV is turned off. Some of these circuits therefore need to be cooled at all times. A low power standby fan may be heard in a quiet environment. This is normal operation.

Custom cabinet installation must allow for proper air circulation around the television.

STAND REQUIREMENT

CAUTION: Mitsubishi TV models WD-52525 and WD-52725 are for use only with Mitsubishi stand, model MB-52525. Mitsubishi TV models WD-62525 and WD-62725 are for use only with Mitsubishi stand model MB-62525. Use with other stands is capable of resulting in instability causing possible injury.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.

Image 2
Contents Owner’s Guide Stand Requirement FCC Declaration of Conformity Contents TV Menu Screen Operations Ieee 1394 Devices and NetCommand Controlled RecordingsSpecial Features Important Safeguards Important Safeguards Our Thanks Mitsubishi Digital Electronics America, IncBack Panel TV Accessories Special Features Front Control PanelTelevision Overview TV Accessories Special FeaturesReset System ResetIndicators Front Control PanelInput Front Panel Inputs and Media Card SlotsMedia Card Slots and Ieee 1394 Input/Output CableCARD Slot Back PanelComponent-1, -2 Inputs Input-1, -2 Monitor OutputDTV Link/IEEE1394 IR Emitter-NetCommandPC Input and Audio DVI Analog AudioConnecting Connecting External Devices & NetCommand Setup ChartConnecting a Wall Outlet Cable or Cable Box Wall Outlet CableUsing a CableCARD CableCARD TechnologyFor antennas with twin flat lead Connecting a Lead Antenna or Separate UHF and VHF AntennaSeparate UHF and VHF Antenna For cable or antenna with coaxial leadConnecting a VCR to an Antenna or Wall Outlet Cable Connecting VCR Video and Audio to a Cable Box Cable Box Back panelConnecting an A/V receiver Connecting a DVD Player with Component DTV Connectors and Adaptors DTV Receiver with Component VideoDTV Receiver to TV Back Panel Connecting a DTV Receiver with RGB, HV VideoDTV Receiver with RGB, HV Video Link Control RS-232C Connection LinkConnecting the IR Emitter NetCommand Quadruple IR Emitter cable is included with the TVDigital Video Signals Connecting Compatible Ieee 1394 DevicesWhen Connecting Ieee 1394 Devices Digital Audio SignalsDirect Device-To-Device Style Pin Style vs -Pin Style ConnectorsConnection Styles Hub Connection StyleConnecting Helpful Hints NetCommand Setup and Editing Using the Remote Control with NetCommand NetCommand Pre-Memorized DevicesRemote Control Functions Overview OverviewInstalling the Batteries Remote Control FunctionsOperation and Care, Sleep TimerFor Best Results from the Remote Control Setting the Sleep TimerNetCommand Setup On Screen Buttons Remote Control Buttons 3D Graphical Menu SystemDevice Setup Screen NetCommand Initial SetupNetCommand Information Screen Welcome ScreenReview Screen Review screenReceiver Inputs Edit NetCommand, Add an A/V ReceiverReceiver Screen Receiver Input Learn Screen Receiver Learn ScreenName Screen Monitor Out to AVR ScreenAdd Screen Edit NetCommand, Add DevicesEdit NetCommand Screen Device Learn Screen Edit NetCommand Add DevicesDevice Screen Device Advanced Learn Screen Connection for Device ScreenInput-DTV Connection Screen VCR for Recordings ScreenRF Connection for Cable Screen IR Code for Device ScreenDelete Device Screen Edit NetCommand, Change or Delete Devices, Finish ScreenChange Device Screen Device Selection Menu Ieee 1394 Devices NetCommand Controlled RecordingsNetCommand Controlled Recordings Disc Search Track List Screen PC ViewingIeee 1394 Devices and NetCommand Control New 1394 Device Screen Adding Ieee 1394 Devices AutomaticallyAdding Ieee 1394 Devices Automatically Name for 1394 Device ScreenIeee 1394 Device Type Screen Connection ScreenPIP Device Selection Menu Power On/Off DevicesDevice Selection Menu IR Controlled Devices Using the Device Menu Button to Display MenusDevice Menu CableCARD MenuDevices 1394 or IR Controlled Using the Guide Button to Display ChannelView and MenusGuide Button ChannelViewRecording Now Record To SetupTime-Delayed Recording Copy-Protected Material Cancel Current RecordingsRecord List Screen Restrictions for Traditional VCRsSetting up a Peer-to-Peer Connection NetCommand Controlled Peer-to-Peer ConnectionsWhat is a Peer-to-Peer Connection? Canceling a Current Peer-to-Peer ConnectionDirect VCR Recording from an Antenna or Cable Source Disc SearchPC Viewing PC InputInserting a media card MediaCommand and Media Card PlaybackMedia Card Slots Don’t pull the media card out while it is playingMedia Command and Media Card Playback TV Menu Screen Operations Main menu, Setup selected Main Menu ChoicesSetup Menu NetCommand Menu Prefer Digital Antenna MenuMemorize ChannelAntenna Menu, SuperQuickView SQV SQV SuperQuickViewTime Menu Captions Menu Analog and Digital Captions Captions Menu, Customizing Digital Settings Entry Chip Lock Menu PasscodeChip Chip Start Time and V-Chip Stop TimeChip Lock Menu V-Chip Definitions Chip Signal InformationContent Categories TV RatingsFront Button Lock Chip Lock MenuLock By Time AudioVideo Menu Analog Only Audio Settings Setting Descriptions AudioAnalog and Digital Audio Setting Digital Only Audio SettingsFor a Currently Viewed PC Setting Descriptions VideoVideo Settings Operation of PIP and POP Warranty IndexDVD Definitions Signals and Formats DefinitionsDisplay Formats Original Signal TV Display FormatsPC Display Formats Device Control with Net Command NetCommand Compatible Traditional Devices AnalogWhen an Ieee 1394 Device is Viewed or Played Ieee 1394 DevicesBypassing Front Button Lock Appendix a Bypassing the V-Chip LockBypassing the V-Chip Lock This page intentionally blank Inputs Appendix B SpecificationsTV Specifications Outputs Appendix CRemote Control Programming Codes Programming the Remote to Control NetCommand A/V ProductsAppendix C Remote Control Programming Codes DVD PlayersMitsubishi A/V Receivers Cable Boxes and Satellite ReceiversReceivers Mitsubishi CD Players Not all functions for all modelsAppendix D On Screen Information Displays Appendix E NetCommand Specialized Device Keys Screen Remote Checkbox NameAppendix F Cleaning and Service To Remove the Diamond Shield To Install the Diamond ShieldAppendix G Diamond Shield Removal For further assistance, call 800Appendix H Filter Cleaning Replace the lamp cartridgeAppendix H Lamp Cartridge Replacement Lamp LifeReplacing the Lamp Cartridge Troubleshooting Problem Possible SolutionTroubleshooting Troubleshooting 100 Using The System Reset Button 101Additional Information 102Index 103104 Icon Order, Viewing, Changing 64 IEEE1394Mitsubishi TV Software 105Mitsubishi DLP Projection Television Limited Warranty 106This Warranty does not Cover 107MDEAservice@mdea.com Website