Manuals / IBM / Computer Equipment / Power Supply

IBM 9179-MHB, 9117-MMB manual The equipment is suitable for installation in the following

Models: 9117-MMB 9179-MHB

1 120

Download 120 pages 7.28 Kb

Page 12

CAUTION:

Data processing environments can contain equipment transmitting on system links with laser modules that operate at greater than Class 1 power levels. For this reason, never look into the end of an optical fiber cable or open receptacle. (C027)

CAUTION:

This product contains a Class 1M laser. Do not view directly with optical instruments. (C028)

CAUTION:

Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following information: laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. (C030)

Power and cabling information for NEBS (Network Equipment-Building System) GR-1089-CORE

The following comments apply to the IBM servers that have been designated as conforming to NEBS (Network Equipment-Building System) GR-1089-CORE:

The equipment is suitable for installation in the following:

vNetwork telecommunications facilities

vLocations where the NEC (National Electrical Code) applies

The intrabuilding ports of this equipment are suitable for connection to intrabuilding or unexposed wiring or cabling only. The intrabuilding ports of this equipment must not be metallically connected to the interfaces that connect to the OSP (outside plant) or its wiring. These interfaces are designed for use as intrabuilding interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling. The addition of primary protectors is not sufficient protection to connect these interfaces metallically to OSP wiring.

Note: All Ethernet cables must be shielded and grounded at both ends.

The ac-powered system does not require the use of an external surge protection device (SPD).

The dc-powered system employs an isolated DC return (DC-I) design. The DC battery return terminal shall not be connected to the chassis or frame ground.

xPower Systems: Power supplies for the 9117-MMB or 9179-MHB

Image 12

IBM 9179-MHB, 9117-MMB manual The equipment is suitable for installation in the following

Contents

Power supplies for the 9117-MMB or 9179-MHB Power SystemsPage Power supplies for the 9117-MMB or 9179-MHB Power SystemsCopyright IBM Corporation 2010 Contents Safety noticesPower supplies for the 9117-MMB or 9179-MHB Notices Safety notices World Trade safety informationGerman safety information Laser safety informationv Do not open or service any power supply assembly 2. Remove the power cords from the outlets3. Remove the signal cables from the connectors 3. Attach the signal cables to the connectorsv Always install stabilizer brackets on the rack cabinet v Always lower the leveling pads on the rack cabinetR001 Install stabilizer brackets on the rack cabinet Remove all devices in the 32U position and abovev Verify that all door openings are at least 760 x 230 mm 30 x 80 in v Do not use a ramp inclined at more than 10 degreesL003 C026The equipment is suitable for installation in the following Power supplies for the 9117-MMB or 9179-MHB Whats new in Power suppliesMarch L003Figure 1. Removing the power supply 2 Power Systems Power supplies for the 9117-MMB or 9179-MHBRelated information Power suppliesFigure 2. Removing the power supply 4 Power Systems Power supplies for the 9117-MMB or 9179-MHBRelated information 3. Connect the power cable A to the power supply 6 Power Systems Power supplies for the 9117-MMB or 9179-MHB Related informationFigure 5. Replacing the power supply Power supply LEDs Related informationDetermine if you are able to perform this procedure concurrently 6. Attach the wrist strap Figure 9. Removing a power supply Power suppliesFigure 10. Fan fault LED and fan identify button 12 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 11. Removing a fan Figure 12. FRU fault and identify LED Related information14 Power Systems Power supplies for the 9117-MMB or 9179-MHB B, shown in Figure 15, is on solid Figure 16. Removing a power supply fan 16 Power Systems Power supplies for the 9117-MMB or 9179-MHBRelated information Determine if you are able to perform this procedure concurrently Figure 18. Replacing a power supply 18 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 17. Replacing a fan 8. Reconnect the power cable A to the front of the power supply, and then slide the cable retention bracket B to the closed position to secure the cable as shown in Figure 19. By moving the bracket to the closed position, you turn on the power supply 11. Close the front rack door Related information 22 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 22. Replacing a fanFigure 23. Replacing a power supply Figure 25. Expansion unit ac power and OCA power LEDs 24 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 26. Fan fault LED Related information26 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 28. Removing an input power distribution assembly cover Figure 29. Removing an input power distribution assembly28 Power Systems Power supplies for the 9117-MMB or 9179-MHB Related informationFigure 30. Replacing an input power distribution assembly Figure 31. Replacing an input power distribution assembly cover30 Power Systems Power supplies for the 9117-MMB or 9179-MHB Related informationFigure 33. Replacing an input power distribution assembly Figure 34. Replacing an input power distribution assembly cover 32 Power Systems Power supplies for the 9117-MMB or 9179-MHBCommon procedures for installable features Before you beginRelated information v Do not open or service any power supply assembly 2. Remove the power cords from the outlets3. Remove the signal cables from the connectors 3. Attach the signal cables to the connectorsv Always install stabilizer brackets on the rack cabinet v Always lower the leveling pads on the rack cabinetR001 To do this, go to the following Web site IBM PrerequisiteIdentifying a part Control panel LEDsFigure 36. Control panel 4. Select Display Previous Diagnostic Results and press Enter Activating the indicator light for the failing partDeactivating the failing-part indicator light Identifying a failing part in an AIX system or logical partitionActivating the failing-part indicator light 1. Sign on to an IBM i session, with at least service level authorityIdentifying a failing part in an IBM i system or logical partition Deactivating the failing-part indicator lightIdentifying a failing part in a Linux system or logical partition Locating a failing part in a Linux system or logical partition40 Power Systems Power supplies for the 9117-MMB or 9179-MHB Related informationIdentifying a part by using the Virtual I/O Server Activating the indicator light for the failing partDeactivating the failing-part indicator light 4. Select Display Previous Diagnostic Results and press EnterStarting the system or logical partition Starting a system that is not managed by an HMC or an SDMCPage Stopping a system or logical partition Stopping a system that is not managed by an HMC or an SDMCStopping a system by using the Hardware Management Console L0032. From the Actions menu, select Operations → Power Off Stopping a system with the Systems Director Management Console46 Power Systems Power supplies for the 9117-MMB or 9179-MHB Related informationFigure 38. Placing the system in the service position 4. Close the front rack door of the unit you are servicing Removing and replacing covers for the 8202-E4B or 8205-E6B Figure 40. Placing the system into the operating positionRemoving the front cover on a stand-alone 8202-E4B or 8205-E6B system Figure 41. Removing the front coverFigure 42. Removing the front cover 52 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 43. Removing the front coverUse this procedure to remove the service access cover Figure 46. Removing the service access cover 54 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 47. Installing the outside service access cover Figure 48. Removing the inside service access coverPower supplies Figure 49. Installing the service access cover 56 Power Systems Power supplies for the 9117-MMB or 9179-MHB5. Place the outside service access cover A on top of the system Disconnecting the power cords from the 8202-E4B or 8205-E6B system Figure 51. Installing the outside service access coverFigure 52. Removing the power cords for a rack-mounted system Figure 53. Removing the power cords for a stand-alone systemPower supplies Connecting the power cords to the 8202-E4B or 8205-E6B system Installing a feature by using the Hardware Management Console3. In the Tasks area expand Serviceability → Hardware → MES Tasks Installing a part by using the Systems Director Management Console Verifying the installed part3. Select Advanced Diagnostics Routines and press Enter 6. Did the Testing Complete, No trouble was found message appear? Did the Resource Repair Action menu appear? No Go to stepv No. This ends the procedure Verifying the installed part in an IBM i system or logical partition 2. Sign on with at least service level authorityDeactivating the failing-part indicator light 1. Sign on to an IBM i session, with at least service level authorityVerifying the installed part in a Linux system or logical partition Verifying an installed part by using stand-alone diagnostics7. At the Diagnostic Operating Instructions display, press Enter Verifying the installed part by using Hardware Management Console 66 Power Systems Power supplies for the 9117-MMB or 9179-MHBActivating and deactivating LEDs by using the HMC 6. Click Close EventDeactivating a system attention LED or partition LED 4. Select Tasks, then Operations, and then Manage Attention LEDViewing serviceable events by using the HMC 2. Select Manage Serviceable Eventsa. Select Actions → View Comments 68 Power Systems Power supplies for the 9117-MMB or 9179-MHBActivating and deactivating LEDs by using the SDMC 6. Click Delete or IgnoreDeactivating a system attention LED or partition LED Activating or deactivating identify LED by using the SDMC 2. Select Actions → Service and Support → Hardware → Identify LED2. Select Actions → System Status and Health → Event Log 70 Power Systems Power supplies for the 9117-MMB or 9179-MHB3. Select Advanced Diagnostics Routines and press Enter 6. Did the Testing Complete, No trouble was found message appear? 72 Power Systems Power supplies for the 9117-MMB or 9179-MHBDid the Resource Repair Action menu appear? No Go to step Verifying a repair Did all the enclosures power on?Did the operating system load successfully? Verifying the repair in AIX 3. Select the Diagnostics Routines option Perform the following steps7. Perform the following steps 76 Power Systems Power supplies for the 9117-MMB or 9179-MHB Did another Resource Repair Action 801015 display? No YesVerifying a repair using an IBM i system or logical partition procedure 78 Power Systems Power supplies for the 9117-MMB or 9179-MHBVerifying the repair in Linux Verifying the repair from the management consoleSelect the function key for Include nonreporting resources Closing a service call v No Go to the HMC isolation procedures. This ends the procedurev No Go to Detecting problems. This ends the procedure 3. Are there any service action events that are open? 18. Click Close Event 82 Power Systems Power supplies for the 9117-MMB or 9179-MHB22. Select the No FRU Replaced for this Serviceable Event option 84 Power Systems Power supplies for the 9117-MMB or 9179-MHB Closing a service call using AIX or Linux Did you encounter any problems? 9. Complete the following steps 88 Power Systems Power supplies for the 9117-MMB or 9179-MHB Closing a service call using Integrated Virtualization Manager 90 Power Systems Power supplies for the 9117-MMB or 9179-MHB 18. Click Close Event 24. Is the error class recorded in step 23 on page 91? Activating and deactivating LEDs 2. Click Actions Service and Support Hardware System Attention LED 3. Open Operations 4. Open LED Status94 Power Systems Power supplies for the 9117-MMB or 9179-MHB 2. Click Actions Service and Support Hardware Identify LED 5. Click Save settings 96 Power Systems Power supplies for the 9117-MMB or 9179-MHBNotices Trademarks Electronic emission noticesClass A Notices Ethernet connection usage restrictionIndustry Canada Compliance Statement Avis de conformité à la réglementation dIndustrie CanadaEuropean Community Compliance Statement VCCI Statement - JapanElectromagnetic Interference EMI Statement - Taiwan Electromagnetic Interference EMI Statement - Peoples Republic of ChinaElectromagnetic Interference EMI Statement - Korea Germany Compliance StatementClass B Notices Electromagnetic Interference EMI Statement - RussiaFederal Communications Commission FCC statement Industry Canada Compliance Statement Avis de conformité à la réglementation dIndustrie CanadaEuropean Community Compliance Statement VCCI Statement - JapanIBM Taiwan Contact Information 104 Power Systems Power supplies for the 9117-MMB or 9179-MHBElectromagnetic Interference EMI Statement - Korea Germany Compliance StatementTerms and conditions 106 Power Systems Power supplies for the 9117-MMB or 9179-MHB Page Printed in USA