Manuals / IBM / Computer Equipment / Power Supply

IBM 9179-MHB, 9117-MMB manual Class B Notices, Electromagnetic Interference EMI Statement - Russia

Models: 9117-MMB 9179-MHB

1 120

Download 120 pages 7.28 Kb

Page 114

Electromagnetic Interference (EMI) Statement - Russia

Verantwortlich für die Einhaltung der EMV Vorschriften ist der Hersteller:

International Business Machines Corp.

New Orchard Road

Armonk, New York 10504

Tel: 914-499-1900

Der verantwortliche Ansprechpartner des Herstellers in der EU ist: IBM Deutschland GmbH

Technical Regulations, Abteilung M456

IBM-Allee 1, 71139 Ehningen, Germany Tel: +49 7032 15-2937

email: tjahn@de.ibm.com

Generelle Informationen:

Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A.

Electromagnetic Interference (EMI) Statement - Russia

Class B Notices

The following Class B statements apply to features designated as electromagnetic compatibility (EMC) Class B in the feature installation information.

Federal Communications Commission (FCC) statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

vReorient or relocate the receiving antenna.

vIncrease the separation between the equipment and receiver.

vConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.

vConsult an IBM-authorized dealer or service representative for help.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from IBM-authorized dealers. IBM is not responsible for

102Power Systems: Power supplies for the 9117-MMB or 9179-MHB

Image 114

IBM 9179-MHB, 9117-MMB manual Class B Notices, Electromagnetic Interference EMI Statement - Russia

Contents

Power supplies for the 9117-MMB or 9179-MHB Power SystemsPage Power supplies for the 9117-MMB or 9179-MHB Power SystemsCopyright IBM Corporation 2010 Contents Safety noticesPower supplies for the 9117-MMB or 9179-MHB Notices German safety information Safety noticesWorld Trade safety information Laser safety information3. Remove the signal cables from the connectors v Do not open or service any power supply assembly2. Remove the power cords from the outlets 3. Attach the signal cables to the connectorsv Always install stabilizer brackets on the rack cabinet v Always lower the leveling pads on the rack cabinetR001 v Verify that all door openings are at least 760 x 230 mm 30 x 80 in Install stabilizer brackets on the rack cabinetRemove all devices in the 32U position and above v Do not use a ramp inclined at more than 10 degreesL003 C026The equipment is suitable for installation in the following March Power supplies for the 9117-MMB or 9179-MHBWhats new in Power supplies L003Figure 1. Removing the power supply 2 Power Systems Power supplies for the 9117-MMB or 9179-MHBRelated information Power suppliesFigure 2. Removing the power supply 4 Power Systems Power supplies for the 9117-MMB or 9179-MHBRelated information 3. Connect the power cable A to the power supply 6 Power Systems Power supplies for the 9117-MMB or 9179-MHB Related informationFigure 5. Replacing the power supply Power supply LEDs Related informationDetermine if you are able to perform this procedure concurrently 6. Attach the wrist strap Figure 9. Removing a power supply Power suppliesFigure 10. Fan fault LED and fan identify button 12 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 11. Removing a fan Figure 12. FRU fault and identify LED Related information14 Power Systems Power supplies for the 9117-MMB or 9179-MHB B, shown in Figure 15, is on solid Figure 16. Removing a power supply fan 16 Power Systems Power supplies for the 9117-MMB or 9179-MHBRelated information Determine if you are able to perform this procedure concurrently Figure 18. Replacing a power supply 18 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 17. Replacing a fan 8. Reconnect the power cable A to the front of the power supply, and then slide the cable retention bracket B to the closed position to secure the cable as shown in Figure 19. By moving the bracket to the closed position, you turn on the power supply 11. Close the front rack door Related information 22 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 22. Replacing a fanFigure 23. Replacing a power supply Figure 25. Expansion unit ac power and OCA power LEDs 24 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 26. Fan fault LED Related information26 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 28. Removing an input power distribution assembly cover Figure 29. Removing an input power distribution assembly28 Power Systems Power supplies for the 9117-MMB or 9179-MHB Related informationFigure 30. Replacing an input power distribution assembly Figure 31. Replacing an input power distribution assembly cover30 Power Systems Power supplies for the 9117-MMB or 9179-MHB Related informationFigure 33. Replacing an input power distribution assembly Figure 34. Replacing an input power distribution assembly cover 32 Power Systems Power supplies for the 9117-MMB or 9179-MHBCommon procedures for installable features Before you beginRelated information 3. Remove the signal cables from the connectors v Do not open or service any power supply assembly2. Remove the power cords from the outlets 3. Attach the signal cables to the connectorsR001 v Always install stabilizer brackets on the rack cabinetv Always lower the leveling pads on the rack cabinet To do this, go to the following Web site IBM PrerequisiteIdentifying a part Control panel LEDsFigure 36. Control panel Deactivating the failing-part indicator light 4. Select Display Previous Diagnostic Results and press EnterActivating the indicator light for the failing part Identifying a failing part in an AIX system or logical partitionIdentifying a failing part in an IBM i system or logical partition Activating the failing-part indicator light1. Sign on to an IBM i session, with at least service level authority Deactivating the failing-part indicator light40 Power Systems Power supplies for the 9117-MMB or 9179-MHB Identifying a failing part in a Linux system or logical partitionLocating a failing part in a Linux system or logical partition Related informationDeactivating the failing-part indicator light Identifying a part by using the Virtual I/O ServerActivating the indicator light for the failing part 4. Select Display Previous Diagnostic Results and press EnterStarting the system or logical partition Starting a system that is not managed by an HMC or an SDMCPage Stopping a system or logical partition Stopping a system that is not managed by an HMC or an SDMCStopping a system by using the Hardware Management Console L00346 Power Systems Power supplies for the 9117-MMB or 9179-MHB 2. From the Actions menu, select Operations → Power OffStopping a system with the Systems Director Management Console Related informationFigure 38. Placing the system in the service position 4. Close the front rack door of the unit you are servicing Removing and replacing covers for the 8202-E4B or 8205-E6B Figure 40. Placing the system into the operating positionRemoving the front cover on a stand-alone 8202-E4B or 8205-E6B system Figure 41. Removing the front coverFigure 42. Removing the front cover 52 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 43. Removing the front coverUse this procedure to remove the service access cover Figure 46. Removing the service access cover 54 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 47. Installing the outside service access cover Figure 48. Removing the inside service access coverPower supplies Figure 49. Installing the service access cover 56 Power Systems Power supplies for the 9117-MMB or 9179-MHB5. Place the outside service access cover A on top of the system Disconnecting the power cords from the 8202-E4B or 8205-E6B system Figure 51. Installing the outside service access coverFigure 52. Removing the power cords for a rack-mounted system Figure 53. Removing the power cords for a stand-alone systemPower supplies Connecting the power cords to the 8202-E4B or 8205-E6B system Installing a feature by using the Hardware Management Console3. In the Tasks area expand Serviceability → Hardware → MES Tasks Installing a part by using the Systems Director Management Console Verifying the installed part3. Select Advanced Diagnostics Routines and press Enter 6. Did the Testing Complete, No trouble was found message appear? Did the Resource Repair Action menu appear? No Go to stepv No. This ends the procedure Deactivating the failing-part indicator light Verifying the installed part in an IBM i system or logical partition2. Sign on with at least service level authority 1. Sign on to an IBM i session, with at least service level authorityVerifying the installed part in a Linux system or logical partition Verifying an installed part by using stand-alone diagnostics7. At the Diagnostic Operating Instructions display, press Enter Verifying the installed part by using Hardware Management Console 66 Power Systems Power supplies for the 9117-MMB or 9179-MHBDeactivating a system attention LED or partition LED Activating and deactivating LEDs by using the HMC6. Click Close Event 4. Select Tasks, then Operations, and then Manage Attention LEDa. Select Actions → View Comments Viewing serviceable events by using the HMC2. Select Manage Serviceable Events 68 Power Systems Power supplies for the 9117-MMB or 9179-MHBActivating and deactivating LEDs by using the SDMC 6. Click Delete or IgnoreDeactivating a system attention LED or partition LED 2. Select Actions → System Status and Health → Event Log Activating or deactivating identify LED by using the SDMC2. Select Actions → Service and Support → Hardware → Identify LED 70 Power Systems Power supplies for the 9117-MMB or 9179-MHB3. Select Advanced Diagnostics Routines and press Enter 6. Did the Testing Complete, No trouble was found message appear? 72 Power Systems Power supplies for the 9117-MMB or 9179-MHBDid the Resource Repair Action menu appear? No Go to step Verifying a repair Did all the enclosures power on?Did the operating system load successfully? Verifying the repair in AIX 3. Select the Diagnostics Routines option Perform the following steps7. Perform the following steps 76 Power Systems Power supplies for the 9117-MMB or 9179-MHB Did another Resource Repair Action 801015 display? No YesVerifying a repair using an IBM i system or logical partition procedure 78 Power Systems Power supplies for the 9117-MMB or 9179-MHBVerifying the repair in Linux Verifying the repair from the management consoleSelect the function key for Include nonreporting resources Closing a service call v No Go to the HMC isolation procedures. This ends the procedurev No Go to Detecting problems. This ends the procedure 3. Are there any service action events that are open? 18. Click Close Event 82 Power Systems Power supplies for the 9117-MMB or 9179-MHB22. Select the No FRU Replaced for this Serviceable Event option 84 Power Systems Power supplies for the 9117-MMB or 9179-MHB Closing a service call using AIX or Linux Did you encounter any problems? 9. Complete the following steps 88 Power Systems Power supplies for the 9117-MMB or 9179-MHB Closing a service call using Integrated Virtualization Manager 90 Power Systems Power supplies for the 9117-MMB or 9179-MHB 18. Click Close Event 24. Is the error class recorded in step 23 on page 91? Activating and deactivating LEDs 2. Click Actions Service and Support Hardware System Attention LED 3. Open Operations 4. Open LED Status94 Power Systems Power supplies for the 9117-MMB or 9179-MHB 2. Click Actions Service and Support Hardware Identify LED 5. Click Save settings 96 Power Systems Power supplies for the 9117-MMB or 9179-MHBNotices Class A Notices TrademarksElectronic emission notices Ethernet connection usage restrictionEuropean Community Compliance Statement Industry Canada Compliance StatementAvis de conformité à la réglementation dIndustrie Canada VCCI Statement - JapanElectromagnetic Interference EMI Statement - Taiwan Electromagnetic Interference EMI Statement - Peoples Republic of ChinaElectromagnetic Interference EMI Statement - Korea Germany Compliance StatementClass B Notices Electromagnetic Interference EMI Statement - RussiaFederal Communications Commission FCC statement European Community Compliance Statement Industry Canada Compliance StatementAvis de conformité à la réglementation dIndustrie Canada VCCI Statement - JapanElectromagnetic Interference EMI Statement - Korea IBM Taiwan Contact Information104 Power Systems Power supplies for the 9117-MMB or 9179-MHB Germany Compliance StatementTerms and conditions 106 Power Systems Power supplies for the 9117-MMB or 9179-MHB Page Printed in USA