Manuals / IBM / Computer Equipment / Power Supply

IBM 9117-MMB manual Industry Canada Compliance Statement, European Community Compliance Statement

Models: 9117-MMB 9179-MHB

1 120

Download 120 pages 7.28 Kb

Page 115

Manual background

any radio or television interference caused by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.

Avis de conformité à la réglementation d'Industrie Canada

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

European Community Compliance Statement

This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards.

This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European Standard EN 55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication equipment.

European Community contact: IBM Deutschland GmbH

Technical Regulations, Department M456 IBM-Allee 1, 71139 Ehningen, Germany Tele: +49 7032 15-2937

email: tjahn@de.ibm.com

VCCI Statement - Japan

Japanese Electronics and Information Technology Industries Association (JEITA) Confirmed Harmonics Guideline (products less than or equal to 20 A per phase)

Notices 103

Image 115

IBM 9117-MMB, 9179-MHB manual Industry Canada Compliance Statement, Avis de conformité à la réglementation dIndustrie Canada

Contents

Power Systems Power supplies for the 9117-MMB or 9179-MHBPage Power Systems Power supplies for the 9117-MMB or 9179-MHBCopyright IBM Corporation 2010 Safety notices ContentsPower supplies for the 9117-MMB or 9179-MHB Notices Laser safety information Safety noticesWorld Trade safety information German safety information3. Attach the signal cables to the connectors v Do not open or service any power supply assembly2. Remove the power cords from the outlets 3. Remove the signal cables from the connectorsv Always lower the leveling pads on the rack cabinet v Always install stabilizer brackets on the rack cabinetR001 v Do not use a ramp inclined at more than 10 degrees Install stabilizer brackets on the rack cabinetRemove all devices in the 32U position and above v Verify that all door openings are at least 760 x 230 mm 30 x 80 inC026 L003The equipment is suitable for installation in the following L003 Power supplies for the 9117-MMB or 9179-MHBWhats new in Power supplies March2 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 1. Removing the power supplyPower supplies Related information4 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 2. Removing the power supplyRelated information 3. Connect the power cable A to the power supply Related information 6 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 5. Replacing the power supply Related information Power supply LEDsDetermine if you are able to perform this procedure concurrently 6. Attach the wrist strap Power supplies Figure 9. Removing a power supply12 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 10. Fan fault LED and fan identify buttonFigure 11. Removing a fan Related information Figure 12. FRU fault and identify LED14 Power Systems Power supplies for the 9117-MMB or 9179-MHB B, shown in Figure 15, is on solid 16 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 16. Removing a power supply fanRelated information Determine if you are able to perform this procedure concurrently 18 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 18. Replacing a power supplyFigure 17. Replacing a fan 8. Reconnect the power cable A to the front of the power supply, and then slide the cable retention bracket B to the closed position to secure the cable as shown in Figure 19. By moving the bracket to the closed position, you turn on the power supply 11. Close the front rack door Related information Figure 22. Replacing a fan 22 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 23. Replacing a power supply 24 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 25. Expansion unit ac power and OCA power LEDsRelated information Figure 26. Fan fault LED26 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 29. Removing an input power distribution assembly Figure 28. Removing an input power distribution assembly coverRelated information 28 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 31. Replacing an input power distribution assembly cover Figure 30. Replacing an input power distribution assemblyRelated information 30 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 33. Replacing an input power distribution assembly 32 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 34. Replacing an input power distribution assembly coverBefore you begin Common procedures for installable featuresRelated information 3. Attach the signal cables to the connectors v Do not open or service any power supply assembly2. Remove the power cords from the outlets 3. Remove the signal cables from the connectorsTo do this, go to the following Web site IBM Prerequisite v Always install stabilizer brackets on the rack cabinetv Always lower the leveling pads on the rack cabinet R001Control panel LEDs Identifying a partFigure 36. Control panel Identifying a failing part in an AIX system or logical partition 4. Select Display Previous Diagnostic Results and press EnterActivating the indicator light for the failing part Deactivating the failing-part indicator lightDeactivating the failing-part indicator light Activating the failing-part indicator light1. Sign on to an IBM i session, with at least service level authority Identifying a failing part in an IBM i system or logical partitionRelated information Identifying a failing part in a Linux system or logical partitionLocating a failing part in a Linux system or logical partition 40 Power Systems Power supplies for the 9117-MMB or 9179-MHB4. Select Display Previous Diagnostic Results and press Enter Identifying a part by using the Virtual I/O ServerActivating the indicator light for the failing part Deactivating the failing-part indicator lightStarting a system that is not managed by an HMC or an SDMC Starting the system or logical partitionPage Stopping a system that is not managed by an HMC or an SDMC Stopping a system or logical partitionL003 Stopping a system by using the Hardware Management ConsoleRelated information 2. From the Actions menu, select Operations → Power OffStopping a system with the Systems Director Management Console 46 Power Systems Power supplies for the 9117-MMB or 9179-MHBFigure 38. Placing the system in the service position 4. Close the front rack door of the unit you are servicing Figure 40. Placing the system into the operating position Removing and replacing covers for the 8202-E4B or 8205-E6BFigure 41. Removing the front cover Removing the front cover on a stand-alone 8202-E4B or 8205-E6B systemFigure 42. Removing the front cover Figure 43. Removing the front cover 52 Power Systems Power supplies for the 9117-MMB or 9179-MHBUse this procedure to remove the service access cover 54 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 46. Removing the service access coverFigure 48. Removing the inside service access cover Figure 47. Installing the outside service access coverPower supplies 56 Power Systems Power supplies for the 9117-MMB or 9179-MHB Figure 49. Installing the service access cover5. Place the outside service access cover A on top of the system Figure 51. Installing the outside service access cover Disconnecting the power cords from the 8202-E4B or 8205-E6B systemFigure 53. Removing the power cords for a stand-alone system Figure 52. Removing the power cords for a rack-mounted systemPower supplies Installing a feature by using the Hardware Management Console Connecting the power cords to the 8202-E4B or 8205-E6B system3. In the Tasks area expand Serviceability → Hardware → MES Tasks Verifying the installed part Installing a part by using the Systems Director Management Console3. Select Advanced Diagnostics Routines and press Enter Did the Resource Repair Action menu appear? No Go to step 6. Did the Testing Complete, No trouble was found message appear?v No. This ends the procedure 1. Sign on to an IBM i session, with at least service level authority Verifying the installed part in an IBM i system or logical partition2. Sign on with at least service level authority Deactivating the failing-part indicator lightVerifying an installed part by using stand-alone diagnostics Verifying the installed part in a Linux system or logical partition7. At the Diagnostic Operating Instructions display, press Enter 66 Power Systems Power supplies for the 9117-MMB or 9179-MHB Verifying the installed part by using Hardware Management Console4. Select Tasks, then Operations, and then Manage Attention LED Activating and deactivating LEDs by using the HMC6. Click Close Event Deactivating a system attention LED or partition LED68 Power Systems Power supplies for the 9117-MMB or 9179-MHB Viewing serviceable events by using the HMC2. Select Manage Serviceable Events a. Select Actions → View Comments6. Click Delete or Ignore Activating and deactivating LEDs by using the SDMCDeactivating a system attention LED or partition LED 70 Power Systems Power supplies for the 9117-MMB or 9179-MHB Activating or deactivating identify LED by using the SDMC2. Select Actions → Service and Support → Hardware → Identify LED 2. Select Actions → System Status and Health → Event Log3. Select Advanced Diagnostics Routines and press Enter 72 Power Systems Power supplies for the 9117-MMB or 9179-MHB 6. Did the Testing Complete, No trouble was found message appear?Did the Resource Repair Action menu appear? No Go to step Did all the enclosures power on? Verifying a repairDid the operating system load successfully? Verifying the repair in AIX Perform the following steps 3. Select the Diagnostics Routines option7. Perform the following steps Did another Resource Repair Action 801015 display? No Yes 76 Power Systems Power supplies for the 9117-MMB or 9179-MHBVerifying a repair using an IBM i system or logical partition 78 Power Systems Power supplies for the 9117-MMB or 9179-MHB procedureVerifying the repair from the management console Verifying the repair in LinuxSelect the function key for Include nonreporting resources v No Go to the HMC isolation procedures. This ends the procedure Closing a service callv No Go to Detecting problems. This ends the procedure 3. Are there any service action events that are open? 82 Power Systems Power supplies for the 9117-MMB or 9179-MHB 18. Click Close Event22. Select the No FRU Replaced for this Serviceable Event option 84 Power Systems Power supplies for the 9117-MMB or 9179-MHB Closing a service call using AIX or Linux Did you encounter any problems? 9. Complete the following steps 88 Power Systems Power supplies for the 9117-MMB or 9179-MHB Closing a service call using Integrated Virtualization Manager 90 Power Systems Power supplies for the 9117-MMB or 9179-MHB 18. Click Close Event 24. Is the error class recorded in step 23 on page 91? Activating and deactivating LEDs 3. Open Operations 4. Open LED Status 2. Click Actions Service and Support Hardware System Attention LED94 Power Systems Power supplies for the 9117-MMB or 9179-MHB 2. Click Actions Service and Support Hardware Identify LED 96 Power Systems Power supplies for the 9117-MMB or 9179-MHB 5. Click Save settingsNotices Ethernet connection usage restriction TrademarksElectronic emission notices Class A NoticesVCCI Statement - Japan Industry Canada Compliance StatementAvis de conformité à la réglementation dIndustrie Canada European Community Compliance StatementElectromagnetic Interference EMI Statement - Peoples Republic of China Electromagnetic Interference EMI Statement - TaiwanGermany Compliance Statement Electromagnetic Interference EMI Statement - KoreaElectromagnetic Interference EMI Statement - Russia Class B NoticesFederal Communications Commission FCC statement VCCI Statement - Japan Industry Canada Compliance StatementAvis de conformité à la réglementation dIndustrie Canada European Community Compliance StatementGermany Compliance Statement IBM Taiwan Contact Information104 Power Systems Power supplies for the 9117-MMB or 9179-MHB Electromagnetic Interference EMI Statement - KoreaTerms and conditions 106 Power Systems Power supplies for the 9117-MMB or 9179-MHB Page Printed in USA