Mitsubishi Electronics WD-62525, WD-52725 manual FCC Declaration of Conformity

Page 3

	FCC Declaration of Conformity
Product:	Projection Television Receiver
Models:	WD-52525, WD-52725, WD-62525, WD-62725
Responsible Party:	Mitsubishi Digital Electronics America, Inc.
	9351 Jeronimo Road
	Irvine, CA 92618-1904
Telephone:	949-465-6000

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

CAUTION: To assure continued FCC compliance, the user must use a shielded video interface cable with bonded ferrite cores at both ends, when using the PC or HDMI input.

Changes or modifications not expressly approved by Mitsubishi could cause harmful interference and would void the user’s authority to operate this equipment.

Image 3

Contents Owner’s Guide Stand Requirement FCC Declaration of Conformity Contents Ieee 1394 Devices and NetCommand Controlled Recordings Special FeaturesTV Menu Screen Operations Important Safeguards Important Safeguards Mitsubishi Digital Electronics America, Inc Our ThanksTV Accessories Special Features Front Control Panel Television OverviewBack Panel Special Features TV AccessoriesFront Control Panel System ResetIndicators ResetFront Panel Inputs and Media Card Slots Media Card Slots and Ieee 1394 Input/OutputInput Input-1, -2 Monitor Output Back PanelComponent-1, -2 Inputs CableCARD SlotDVI Analog Audio IR Emitter-NetCommandPC Input and Audio DTV Link/IEEE1394Connecting Chart Connecting External Devices & NetCommand SetupWall Outlet Cable Connecting a Wall Outlet Cable or Cable BoxCableCARD Technology Using a CableCARDFor cable or antenna with coaxial lead Connecting a Lead Antenna or Separate UHF and VHF AntennaSeparate UHF and VHF Antenna For antennas with twin flat leadConnecting a VCR to an Antenna or Wall Outlet Cable Cable Box Back panel Connecting VCR Video and Audio to a Cable BoxConnecting an A/V receiver Connecting a DVD Player with Component DTV Receiver with Component Video DTV Connectors and AdaptorsConnecting a DTV Receiver with RGB, HV Video DTV Receiver with RGB, HV VideoDTV Receiver to TV Back Panel Link Link Control RS-232C ConnectionQuadruple IR Emitter cable is included with the TV Connecting the IR Emitter NetCommandDigital Audio Signals Connecting Compatible Ieee 1394 DevicesWhen Connecting Ieee 1394 Devices Digital Video SignalsHub Connection Style Pin Style vs -Pin Style ConnectorsConnection Styles Direct Device-To-Device StyleConnecting Helpful Hints NetCommand Setup and Editing NetCommand Pre-Memorized Devices Using the Remote Control with NetCommandOverview Remote Control Functions OverviewSetting the Sleep Timer Remote Control FunctionsOperation and Care, Sleep TimerFor Best Results from the Remote Control Installing the BatteriesNetCommand Setup On Screen Buttons 3D Graphical Menu System Remote Control ButtonsWelcome Screen NetCommand Initial SetupNetCommand Information Screen Device Setup ScreenReview screen Review ScreenEdit NetCommand, Add an A/V Receiver Receiver ScreenReceiver Inputs Receiver Learn Screen Receiver Input Learn ScreenMonitor Out to AVR Screen Name ScreenEdit NetCommand, Add Devices Edit NetCommand ScreenAdd Screen Edit NetCommand Add Devices Device ScreenDevice Learn Screen Connection for Device Screen Device Advanced Learn ScreenIR Code for Device Screen VCR for Recordings ScreenRF Connection for Cable Screen Input-DTV Connection ScreenEdit NetCommand, Change or Delete Devices, Finish Screen Change Device ScreenDelete Device Screen Disc Search Track List Screen PC Viewing Ieee 1394 Devices NetCommand Controlled RecordingsNetCommand Controlled Recordings Device Selection MenuIeee 1394 Devices and NetCommand Control Name for 1394 Device Screen Adding Ieee 1394 Devices AutomaticallyAdding Ieee 1394 Devices Automatically New 1394 Device ScreenConnection Screen Ieee 1394 Device Type ScreenPower On/Off Devices Device Selection MenuPIP Device Selection Menu CableCARD Menu Using the Device Menu Button to Display MenusDevice Menu IR Controlled DevicesChannelView Using the Guide Button to Display ChannelView and MenusGuide Button Devices 1394 or IR ControlledRecord To Setup Time-Delayed RecordingRecording Now Restrictions for Traditional VCRs Cancel Current RecordingsRecord List Screen Copy-Protected MaterialCanceling a Current Peer-to-Peer Connection NetCommand Controlled Peer-to-Peer ConnectionsWhat is a Peer-to-Peer Connection? Setting up a Peer-to-Peer ConnectionDisc Search Direct VCR Recording from an Antenna or Cable SourcePC Input PC ViewingDon’t pull the media card out while it is playing MediaCommand and Media Card PlaybackMedia Card Slots Inserting a media cardMedia Command and Media Card Playback TV Menu Screen Operations Main Menu Choices Main menu, Setup selectedSetup Menu NetCommand Menu Channel Antenna MenuMemorize Prefer DigitalSQV SuperQuickView Antenna Menu, SuperQuickView SQVTime Menu Captions Menu Analog and Digital Captions Captions Menu, Customizing Digital Settings Chip Start Time and V-Chip Stop Time Chip Lock Menu PasscodeChip EntryTV Ratings Chip Signal InformationContent Categories Chip Lock Menu V-Chip DefinitionsChip Lock Menu Lock By TimeFront Button Lock AudioVideo Menu Digital Only Audio Settings Setting Descriptions AudioAnalog and Digital Audio Setting Analog Only Audio SettingsSetting Descriptions Video Video SettingsFor a Currently Viewed PC Operation of PIP and POP Index WarrantySignals and Formats Definitions Display FormatsDVD Definitions TV Display Formats Original SignalPC Display Formats NetCommand Compatible Traditional Devices Analog Device Control with Net CommandIeee 1394 Devices When an Ieee 1394 Device is Viewed or PlayedAppendix a Bypassing the V-Chip Lock Bypassing the V-Chip LockBypassing Front Button Lock This page intentionally blank Appendix B Specifications TV SpecificationsInputs Outputs Programming the Remote to Control NetCommand A/V Products Appendix CRemote Control Programming CodesDVD Players Appendix C Remote Control Programming CodesMitsubishi CD Players Not all functions for all models Cable Boxes and Satellite ReceiversReceivers Mitsubishi A/V ReceiversAppendix D On Screen Information Displays Screen Remote Checkbox Name Appendix E NetCommand Specialized Device KeysAppendix F Cleaning and Service For further assistance, call 800 To Install the Diamond ShieldAppendix G Diamond Shield Removal To Remove the Diamond ShieldReplace the lamp cartridge Appendix H Filter CleaningLamp Life Appendix H Lamp Cartridge ReplacementReplacing the Lamp Cartridge Problem Possible Solution TroubleshootingTroubleshooting Troubleshooting 100 101 Using The System Reset Button102 Additional Information103 IndexIcon Order, Viewing, Changing 64 IEEE1394 104105 Mitsubishi TV Software106 Mitsubishi DLP Projection Television Limited Warranty107 This Warranty does not CoverWebsite MDEAservice@mdea.com