Epson LVP-X200A user manual To operate projector power on, Left side, Button, Lamp Power

Page 16

To operate projector power ON

Numbers 1 - 9 correspond to the instruction numbers below.

ENGLISH

2, 9

Left side

		INPUT1 INPUT2	MAIN
RGB1 IN	AUDIO	AUDIO
		O	I
		L
RGB2 IN		R
		AC IN
		VIDEO
RGB OUT
		S-VIDEO
	RS-232C 1	RS-232C 2

LINE -OUT

LAMP	TEMP	CARD 1	CARD 2
RGB	VIDEO CARD	MENU	FINE	FOCUS	AUTO
RGB	VIDEO CARD	MENU	FINE	/ZOOM	POSITION

ENTER

3,7,8 4 4	6 5	AUTO position
		button

1.Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.

2.Turn on the equipment connected to the projector.

3.Turn the projector on by pressing the POWER but- ton.

The light source lamp starts warming up, eventu- ally turn on. In cases where light source lamp does not come on, wait for one minute before switching power on again.

•If power to the main unit is turned off within two minutes of turning off the light source lamp, power will not be introduced to the lamp for one minute the next time the main unit power switch is turned on. When this happens, the indicator lamp will blink for one minute.

	indicator	LAMP	POWER
	condition	LAMP	POWER
	condition
	stand-by	-	red
	when light source lamp is on	green	green
	when light source lamp does not light up	-	red

Important:

•A darkened image may be seen right after pressing the POWER button due to warming up of this pro- jector. When warming up, no other commands can be accepted.

•When the lamp indicator is blinking red, the ser- vice life of the lamp is about to end. Replace the lamp. See pages 40 and 44.

•The picture might not be of optimum performance in extreme hot or cold conditions. (The projector is not malfunctioning.)

4.Select the desired external input source by using the RGB or VIDEO button.

•The projector automatically selects the appropriate signal system. The selected signal system is dis- played on the SIGNAL menu.

•When selecting the RGB1 or RGB2 input, the im- age may be flickered. Press the FINE buttons to adjust the image.

•Press CARD button to see the PC CARD images. (You cannot select it when CARD 1 or CARD 2 indi- cator is not lighting up.)

16

Image 16

Contents X200 English Contents Important safeguards Never remove the cabinet Do not modify this equipmentIf you break or drop the cabinet Do not face a lens to the sunOverview of the projector FINE, º, ª, FOCUS/ZOOM and Auto Position buttonsMain power Power jackPC card eject PC card insert slotOverview of the remote control RGB, VIDEO, CardBattery installation Operation areaPreparing the projector for operation Orientation of the projectorFront projection Front projection, ceiling mountGetting ready for projection Adjusting the angle of projectionGround terminal Basic connections Projector + AV equipmentCables and adapters Projector + DVD playerProjector + IBM PC or IBM PC compatibles Desktop computerPower Book When outputting to both a PC monitor and the projectorBasic connections continue Projector + MacintoshDesktop computer display connector Projector + NEC PC-98 seriesTo operate projector power on Lamp PowerLeft side ButtonTurning off the projector Volume from the speakerAuto Position button Menu operation Basic operationPicture BrightnessSignal PictureInstallation PinP/EXPANDPC Card Auto Play AudioOption VerPicture adjustment Adjustment from personal computerAdjusting the images form personal Computers in Menu displayCGA70 Gamma Correction menu MasterAdvanced feature for presentation Cursor operationStill Fast SlowSetting the Expand mode Using the Expand modeIndication Mode 4 actual size display Super impose Picture in PictureUsing the PC-CARD Setting up the PC-CARDRelease the PC-CARD Play backPC-CARD Continue Card Auto PlayAdvanced feature with PC Installation of softwarePCV PC Card Viewer EnvironmentCommand reference For Windows Starting up PCV For WindowsRecording the image For Windows Editing the presentation For Windows Command reference Starting up PCV For MacintoshRecording the image For Macintosh JpegPCV Editing the presentation For MacintoshSequencing Exchange images Pcgc Personal Computer Graphic Control ConnectionStarting up Pcgc SpacePointer Projector + NEC PC 98 seriesSetting of SpacePointer Operation of PC by remote controlFor Windows Uninstallation of software Replacement of a light source lamp How to reset the operation time meter Life of the lampMaintenance Cleaning the air-filterCleaning the projector and the ventilation slots Cleaning the lensTroubleshooting Problems Cause Possible SolutionsIndicators Indicator Shows Condition Possible SolutionsIndicator TempSpecifications Replacement parts listAccessories LVP-X200A