Davis Instruments Vantage Pro2 manual Console Location, Tested and established, Cabled console

Page 9

Console Location

 

To ISS

 

2. Ensure that the ISS cable is not twisted through the access port.

 

 

Note:

The ISS must be assembled and connected to the console so that it is receiving

 

power before the console connection can be tested.

 

 

 

Once the console and ISS are both powered up, cable connection should be

 

tested and established.

 

Once the console is powered, it automatically enters Setup Mode. You can

 

step through the Setup Mode options, or exit the Setup Mode to test the

 

connection and sensor readings in Current Weather Mode. See “Setup

 

Mode” on page 9 for Setup Mode options. See “Current Weather Mode” on

 

page 20 for viewing and verifying current weather data coming from the

 

cabled console.

 

To verify that the console is receiving data from the ISS through the con-

 

sole connection, see “Cabled ISS Assembly” in the Integrated Sensor Suite

 

Installation Manual.

Console Location

You should place the console in a location where the keyboard is easily accessible and the display is easy to read. For more accurate readings, fol- low these suggestions.

Avoid placing the console in direct sunlight. This may cause erroneous inside temperature and humidity readings and may damage to the unit.

Avoid placing the console near radiators or heating/air conditioning ducts.

If you are mounting the console on a wall, choose an interior wall. Avoid exterior walls that tend to heat up or cool down depending on the weather.

If you have a wireless console, be aware of possible interference from cordless phones or other devices. To prevent interference, maintain a distance of 10 feet between the Vantage Pro2 console and a cordless phone (handset and base).

6

Image 9
Contents Vantage Pro2 Console Manual Vantage Pro 2 Console Manual Vantage Pro2 Console Display FeaturesTable of Contents Chapter Welcome to Vantage Pro2 Console FeaturesKeyboard & Display Printed on that keyConsole Modes Vantage Pro OptionsOptional Sensors Optional WeatherLink SoftwareOptional Accessories Powering the Console Chapter Installing the ConsoleInstalling the AC Power Adapter Ies provide backup power for up to four to six weeksConnecting Cabled Stations Installing BatteriesConsole Location Installation ManualTested and established Cabled consoleTable & Shelf Placement Wall Mounting Chapter Using Your Weather Station Setup ModeSetup Mode Commands Screen 1 Active Transmitters Screen 1 Active TransmittersScreen 2 Configuring Transmitter IDs Wireless Only Screen 3 Retransmit Wireless OnlyScreen Screen 4 Time & Date Screen 5 Latitude Screen 7 Time Zone Screen 6 LongitudeScreen 8 Daylight Savings Settings Screen 10 Elevation Screen 9 Daylight Savings StatusScreen 11 Wind Cup Size Screen 12 Rain Collector Press and release 2ND and press Units once Data logger installed on the consoleScreen 13 Rain Season Screen 14 Serial Baud RateClear All Command Current Weather ModeSelecting Weather Variables Selecting Units of MeasurePress Wind to select wind speed Selected variable’s units will change. RepeatWind Chill is displayed in either Fahrenheit ºF or Cen Press 2ND then press Chill to select Wind ChillPress 2ND then press Heat to display the Heat Index Press Rainday to display the rain accumulated since 12 mid Night. Any rain accumulated in the last 24 hours displaysTicker at the bottom of the screen Screen display. Press 2ND then Lamps again to turn the back Press 2ND then press Lamps to turn on the backlight forCalibrating Temperature And Humidity Calibrating, Setting, and Clearing VariablesDisplaying the Forecast Displaying Time & Date or Sunrise & SunsetAfter a moment, the variable you’ve selected begins Calibrate Wind Direction ReadingReading Setting Weather Variables Calibrating Barometric PressureClearing Weather Variables Highs and Lows Mode Viewing Highs and Lows Four Special Alarms Alarm ModeSetting Alarms Setting the Time AlarmClearing Alarm Settings Graph Mode Silencing AlarmsPress Done to silence an alarm when it sounds Viewing Graphs Weather Variable Available Graphs Chapter Troubleshooting and Maintenance Vantage Pro2 Troubleshooting GuideProblem Solution Rain Accessible to a cabled weather station Console Diagnostic ScreensNumber of missed data packets Number of packets containing errors that were receivedReception Diagnostic Screen One Year Limited Warranty Console MaintenanceAppendix a Weather Data Sor 30% even though water vapor content does not changeTive humidity Ity has a large capacity to absorb extra water vaporBarometric Pressure Pro2 displays UV readings in two scales MEDs and UV Index MED for persons with very light skinSkin Phototype Skin color Tanning & Sunburn history III Skin Type Skin Color History of Tanning & SunburningIndex Values Exposure Category Appendix B Specifications Wireless Communication SpecificationsConsole Console Data Display Specifications Variable Required Sensors Weather Data SpecificationsThsw Forecast Vantage Pro2 Console Icons