Eiki EIP-3500 owner manual Introduction

Page 5
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY

Before using the projector, please read this operation manual carefully.

Introduction

ENGLISH

1.WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2.CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification, or

recall that EIKI may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equip- ment.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verification.

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

1

Image 5
Contents EIP-3500 Model No. EIP-3500 Serial No Special Note for Users in the U.K Page Introduction Product Disposal Operation Buttons used in thisContents Reference Important Safeguards Do not block the intake and exhaust vents Rest your eyes occasionallyAvoid locations with extremes of tem- perature Other connected equipment Using the projector in other countriesTemperature monitor function Setup Guide Optional accessory AccessoriesSupplied accessories Projector Part Names and FunctionsLamp indicator About the Indicators on the ProjectorTerminals Projector Rear ViewCLICK/ENTER button 24·40 Remote ControlUsable Range Using the Remote ControlInserting the Batteries Insert the batteriesQuick Start Setup and ProjectionAdjust the angle Pocket of the storage case Close the cover of the storageCase Setting up the Projector Setting up the ProjectorProjection from behind the Screen Projecting a Reversed ImageINPUT/OUTPUT Terminals and Connectable Main Equipment ConnectionsAudio Input Samples of Cables for ConnectionSupplied Accessories Connecting to a ComputerUsing the Remote Control as the Wireless Computer Mouse Supplied Accessory Connecting to Video EquipmentWhen connecting video equipment with S-video output terminal When connecting video equipment with video output terminalControlling the Projector by a Computer When connecting to the LAN terminal using a LAN cableConnecting to an Amplifier or Other Audio Equipment Connecting to a Monitor with RGB Input TerminalTurning the Power off Putting Connecting the Power CordTurning the Projector On/Off Turning the Projector onHeight Adjust button Using the Adjustment FeetRear adjustment feet Image ProjectionPress Correcting Trapezoidal DistortionKeystone button Undo buttonAdjusting the Projected Image Size Adjusting the FocusPress on the projector or on the remote control Focus buttons Zoom buttons Auto Focus buttonAdjusting the Volume Switching the Input ModeVolume buttons Input buttonsPress on the remote control to cancel the operation Press on the remote controlDisplaying an Enlarged Portion of an Image AV Mute buttonSwitching the High Brightness/High Contrast Mode Selecting the Picture ModeFreeze button Undo button Picture Mode button Iris button Freezing a Moving ImageMOUSE/Adjustment Resize ModeButton //\ Undo button Resize buttonVideo Following shows the items that can be set in the projector When using the Input 1 or Input 2 modeMenu Items Options1 menu Menu Selections Adjustments Using the Menu ScreenExample Adjusting Bright Example Picture screen menu for Input 1 RGB mode Menu iconsPress or to select the item you want to adjust To adjust the pro- jected image while viewing itPress \ or to adjust the item selected Single adjustment itemsExample Setting Menu Position Menu Selections SettingsSub menu Adjusting the Image Picture Adjustment Picture menuEmphasizing the Contrast Adjusting the Color TemperatureSwitching the High Bright- ness/High Contrast Mode SRGB SettingExample Picture screen menu for IN- PUT 1 RGB mode Description of Iris SettingsRGB Signal Type SettingAdjusting the Computer Image Computer Image Adjustment Fine Sync menuSpecial Modes Setting Example Fine Sync screen menu for Input 1 RGB modeChecking the Input Signal Auto Sync AdjustmentChecking the Lamp Life Status Using the Options1 MenuSetting the Resize Mode Setting the Video System Setting On-screen DisplaySelecting a Startup and Background Image Eco ModeSelecting the Menu Screen Position Auto Power Off FunctionWhen the System Lock is set Example Options1 screen menu for Input 1 RGB modeSystem Lock Function Select System Lock on the Op Tions1 menu, then pressChanging the keycode When System Lock is set Example Options2 screen menu Setting a PasswordIf You Forget Your Password Auto Keystone Setting Auto Focus SettingExample Options2 screen menu Description of Auto Focus Example Options2 screen menu Description of Auto KeystoneSetting the Audio Output Type Speaker SettingSelecting the Transmis- sion Speed RS-232C Reversing/Inverting Pro- jected ImagesExample Options2 screen menu Description of PRJ Modes Example Options2 screen menu Description of RS-232CLAN/RS232C Setting Monitor Output SettingsExample Options2 screen menu Description of Monitor Out Description of LAN/RS232CConfirming the Network In- formation for the Projector Selecting the On-screen Display Language Using the Language MenuPress \ or to select the Lan- guage menu icon Press or to select the desired Language, and then pressCleaning the projector MaintenanceCleaning the lens Cleaning the exhaust and intake ventsAbout the lamp indicator Maintenance IndicatorsAbout the temperature warning indicator Abnormal Regarding the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer Computer Computer Compatibility ChartRemote control batteries have run out TroubleshootingInput 2 RGB NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM SpecificationsGlossary 32,57 IndexEastern Europe CanadaDeutschland & Österreich Japan & Worldwide