Eiki EIP-3500 owner manual Regarding the Lamp

Page 70

Regarding the Lamp

Lamp

■It is recommended that the lamp unit (optional: AH-35001) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 50.

■Purchase a replacement lamp unit of type AH-35001 from your place of purchase, nearest EIKI Au- thorized Dealer or Service Center.

Caution Concerning the Lamp

■This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

■Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest EIKI Authorized Dealer or Service Center to assure safe operation.

Replacing the Lamp

Caution

•Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury.

•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

■Carefully change the lamp by following the instructions described in this section. *If you wish, you may have the lamp replaced at your nearest EIKI Authorized Dealer or Service Center.

*If the new lamp does not illuminate after replacement, take your projector to the nearest EIKI Authorized Dealer or Service Center for repair.

66

Page 69 Page 71
Image 70
Page 69 Page 71
Contents EIP-3500 Model No. EIP-3500 Serial No Special Note for Users in the U.K Page Introduction Product Disposal Buttons used in this OperationContents Reference Important Safeguards Avoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the intake and exhaust vents Temperature monitor function Using the projector in other countriesOther connected equipment Setup Guide Supplied accessories AccessoriesOptional accessory Part Names and Functions ProjectorAbout the Indicators on the Projector Lamp indicatorProjector Rear View TerminalsRemote Control CLICK/ENTER button 24·40Inserting the Batteries Using the Remote ControlUsable Range Insert the batteriesSetup and Projection Quick StartAdjust the angle Case Close the cover of the storagePocket of the storage case Setting up the Projector Setting up the ProjectorProjecting a Reversed Image Projection from behind the ScreenConnections INPUT/OUTPUT Terminals and Connectable Main EquipmentSamples of Cables for Connection Audio InputConnecting to a Computer Supplied AccessoriesUsing the Remote Control as the Wireless Computer Mouse Connecting to Video Equipment Supplied AccessoryWhen connecting video equipment with video output terminal When connecting video equipment with S-video output terminalWhen connecting to the LAN terminal using a LAN cable Controlling the Projector by a ComputerConnecting to a Monitor with RGB Input Terminal Connecting to an Amplifier or Other Audio EquipmentTurning the Projector On/Off Connecting the Power CordTurning the Power off Putting Turning the Projector onRear adjustment feet Using the Adjustment FeetHeight Adjust button Image ProjectionKeystone button Correcting Trapezoidal DistortionPress Undo buttonPress on the projector or on the remote control Adjusting the FocusAdjusting the Projected Image Size Focus buttons Zoom buttons Auto Focus buttonVolume buttons Switching the Input ModeAdjusting the Volume Input buttonsDisplaying an Enlarged Portion of an Image Press on the remote controlPress on the remote control to cancel the operation AV Mute buttonFreeze button Undo button Picture Mode button Iris button Selecting the Picture ModeSwitching the High Brightness/High Contrast Mode Freezing a Moving ImageButton //\ Resize ModeMOUSE/Adjustment Undo button Resize buttonVideo Menu Items When using the Input 1 or Input 2 modeFollowing shows the items that can be set in the projector Options1 menu Example Adjusting Bright Using the Menu ScreenMenu Selections Adjustments Example Picture screen menu for Input 1 RGB mode Menu iconsPress \ or to adjust the item selected To adjust the pro- jected image while viewing itPress or to select the item you want to adjust Single adjustment itemsMenu Selections Settings Example Setting Menu PositionSub menu Picture Adjustment Picture menu Adjusting the ImageAdjusting the Color Temperature Emphasizing the ContrastExample Picture screen menu for IN- PUT 1 RGB mode SRGB SettingSwitching the High Bright- ness/High Contrast Mode Description of Iris SettingsSignal Type Setting RGBSpecial Modes Setting Computer Image Adjustment Fine Sync menuAdjusting the Computer Image Example Fine Sync screen menu for Input 1 RGB modeAuto Sync Adjustment Checking the Input SignalSetting the Resize Mode Using the Options1 MenuChecking the Lamp Life Status Setting On-screen Display Setting the Video SystemEco Mode Selecting a Startup and Background ImageAuto Power Off Function Selecting the Menu Screen PositionSystem Lock Function Example Options1 screen menu for Input 1 RGB modeWhen the System Lock is set Select System Lock on the Op Tions1 menu, then pressChanging the keycode When System Lock is set If You Forget Your Password Setting a PasswordExample Options2 screen menu Example Options2 screen menu Description of Auto Focus Auto Focus SettingAuto Keystone Setting Example Options2 screen menu Description of Auto KeystoneSpeaker Setting Setting the Audio Output TypeExample Options2 screen menu Description of PRJ Modes Reversing/Inverting Pro- jected ImagesSelecting the Transmis- sion Speed RS-232C Example Options2 screen menu Description of RS-232CExample Options2 screen menu Description of Monitor Out Monitor Output SettingsLAN/RS232C Setting Description of LAN/RS232CConfirming the Network In- formation for the Projector Press \ or to select the Lan- guage menu icon Using the Language MenuSelecting the On-screen Display Language Press or to select the desired Language, and then pressCleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsAbout the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator Abnormal Regarding the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer Computer Compatibility Chart ComputerTroubleshooting Remote control batteries have run outInput 2 RGB Specifications NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAMGlossary Index 32,57Deutschland & Österreich CanadaEastern Europe Japan & Worldwide
Top Page Image Contents